manualshive.com logo in svg

Simrad AP50, Installation Manual

Share
Download
Simrad AP50 Installation Manual Download Page 127

Simrad AP50 Autopilot 

118 

20222410 / B

 

7.3

 

Failure Mode Effect Analyses 

Should a technical fault occur, provisions have been made for 
safe operation according to the following table: 

 

Cause of failure 

Effect 

Power failure in autopilot supply 

Acoustic POWER FAILURE ALARM 
given (operated by separate alarm 
supply) 

Ship does not respond to rudder 
command 

“Vessel of course” alarm given when off 
course limit exceeded during transit 

Analog board: 

Processor stop or software lockup 

Analog command line open after approx. 
1 sec. or signal frozen (depends on 
setting of switch S6 on the JD53 Dual 
Analog Board). 

Watchdog restart after 1.6 seconds. 

“No rudder response” alarm after 5 sec. 

Analog board: 

Data line or power line open in 
internal bus cable 

After 5 sec: 

Analog command lines open, signal 
level frozen. 

Steering gear Mode1 and Mode2 go off. 

“No rudder response” alarm 

Analog board: 

Missing reference voltage for 
rudder control electronics. 

“No rudder cntrl voltage” alarm. 

Analog command lines open, signal 
level frozen. 

Solid state board: 

Missing supply, blown fuse, broken 
connection, defect drive 
electronics. 

“No rudder response” alarm. 

 

 

 

 

 

Summary of Contents for AP50















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands