background image

Prestige, Conquest, & Broadmoor Series

1/2003

21

TP 300-2534-02-PR-SMA

Arbor Drive Belt Replacement - 
44”, 50”, & 54” Mowers

NOTE: Be sure to use only genuine Simplicity replace-
ment parts.  

1. Park the tractor on a smooth, level surface such as a

concrete floor. Disengage the PTO, turn off the
engine and lock the parking brake. Remove the key.

2. Remove the mower from the tractor. See Mower

Removal in the Operation section.

44” & 50” MODELS

3. Remove the capscrews securing the right-hand arbor

cover (B, Figure 46). Remove three capscrews secur-
ing left-hand arbor cover (D).

54” MODELS

3. Remove the PTO belt.  Remove the taptite screws

(A, Figure 47) securing the belt covers and remove
the belt covers (B, D).

ALL MODELS

4. Using a pair of locking pliers or a spring puller,

remove the idler pulley spring (C, Figures 46, 47)
from slot in deck.

5. Loosen capscrew (A, Figure 46) securing the idler

pulley to the bracket. The belt can now be slipped
between the pulley and idler bracket hub.

6. Install a new belt as shown in Figure 48. Make sure

that V-side of belt runs in arbor pulley (A) grooves
and flat side of belt runs against idler pulley (B).  

7. Tighten the capscrew (A, Figure 46).

FRONT

Figure 48. Mower Deck Drive Belt Routing All Models
A. Arbor Drive Pulley (V-sided)
B. Idler Pulley (Flat-sided)

A

A

A

B

Figure 47.  Mower Deck - 54” Mowers
A. Taptite Screws
B. Right-hand Arbor Cover
C. Spring
D. Left-hand Arbor Cover
E. Alignment Notches

D

B

C

A

Figure 46. Mower Deck - 44" & 50” Mowers
A. Capscrew
B. Right-hand Arbor Cover
C. Spring
D. Left-hand Arbor Cover

E

E

B

A

D

C

8. Reinstall spring (C, Figures 46, 47) into its slot in

mower deck.

9. Reinstall the left and right arbor covers (B and D,

Figures 46, 47).  54” Models: To provide proper belt
cover clearance, make sure the alignment notches
(E, Figure 47) are centered on the taptite screws (A).

10. Install the mower onto the tractor.

A

Summary of Contents for Broadmoor 1600 Series





























Reviews: