background image

 

dst  

dst [options]: Used to configure and display the 
Clock's Daylight Saving Time settings. 
 

 
While in Daylight Saving Time, one hour is added 
to the time display. 
 

 

Disable the Daylight Saving Time 
adjustment. [dst -none] 

 

Enable Daylight Saving Time for the United 
States or Canada using March, 2007 rules. 
[raw -1

 

8

 

2

 

2

 

1

 

1

 

10

 

2] 

 

Enable Daylight Saving Time for the 
European Union or United Kingdom. [dst -eu] 

 

For other locations use the online DST 
calculator at 

www.buyinova.com/calculator

 

to compute the correct eight (8) digit DST 
configuration rule. [dst –raw] 

 
Note: In firmware Versions 1.0 and 1.1, disregard 
the   

-us DST macro

 and the 

–raw telnet help

;  

both contain errors.  Use the online DST 
calculator at 

www.buyinova.com/calculator

 

to 

determine the correct eight (8) digit 
configuration rule for your location. 
 

 

help 

Displays help information 

ipconfig 

ipconfig [options]: 

Used to configure 

Configure or 

display the network settings. 

 

 

 

[-d] Use DHCP to lease an IP address and 
retrieve network settings. 
 

 

[-a IP] Use the specified fixed IP address. 
(Disables DHCP) 
 

 

[-m mask] Set the subnet mask.           
(Ignored if DHCP is enabled) 
 

 

[-g gateway] Set the gateway 
address.(Ignored if DHCP is enabled) 
 

 

[-n domainname] Set domain name.             
(Ignored if DHCP is enabled) 
 

 

[-p IP]Set primary DNS address.       
(Ignored if DHCP is enabled) 
 

 

[-s IP]Set secondary DNS address.     
(Ignored if DHCP is enabled) 
 

 

[-t dnstimeout]Set DNS timeout (0 is 
valid).  (Ignored if DHCP is enabled) 

©2007 Simplex Time Recorder Co.  All rights reserved.                                                                            

Page 17

 

Summary of Contents for 715437
























Reviews: