background image

Appendix

BA_PA-KL²-x-xx_EN_10 

www.simon-protec.com

 

Date: 09.06.2020 

 

[email protected]

 

Issue: 1.0 / 06.2020

Page 10

4.  Appendix

4.1.  Care and Maintenance

See supplementary sheet “Safety instructions and warranty 

conditions!

short.simon-protec.com/sugen

4.2.  General business and 

delivery terms

Deliveries and services are subject to the currently appli-

cableterms for products and services of the electrical in-

dustry (green  delivery  terms),  including  the  supplementary 

clause“Extended retention of title”. These are published by 

the German Electrical and Electronic Manufacturers‘ Asso-

ciation (ZVEI),  Frankfurt.  If  you  are  not  aware  of  these,  we 

will gladlysend them to you. You can also download these 

agreements
from

short.simon-protec.com/agben

 

The place of jurisdiction is Passau.

4.3.  Company addresses

4.3.1.  System manufacturer

SIMON PROtec Systems GmbH

 

Medienstraße 8 

94036 Passau

Tel.: +49 (0) 851 988 70 - 0

 

Fax: +49 (0) 851 988 70 - 70
E-Mail: [email protected] 

Internet: www.simon-protec.com

4.3.2.  Germany

SIMON PROtec Deutschland GmbH

 

Medienstraße 8 

94036 Passau

Tel.: +49 (0) 851 379 368 - 0

 

Fax: +49 (0) 851 379 368 - 70

SIMON PROtec Deutschland GmbH

 

Fraunhoferstraße 14 

82152 Planegg-Martinsried 

Tel.: +49 (0) 89 791 70 11

 

Fax: +49 (0) 89 791 79 72
E-Mail: [email protected] 

Internet: www.simon-protec.de

4.3.3.  Switzerland

SIMON PROtec Systems AG

 

Allmendstrasse 38 

8320 Fehraltorf

Tel.: +41 (0) 44 956 50 30

 

Fax: +41 (0) 44 956 50 40
E-Mail: [email protected] 

Internet: www.simon-protec.ch

4.3.4.  Hungary

SIMON PROtec Systems Kft.

 

Sodras utca 1. fszt. 1 

1026 Budapest

Tel.: +36 (0) 30 552 0424

E-Mail: [email protected] 

Internet: www.simon-protec.hu

5.  Manufacturer‘s declaration

We hereby declare that the product complies with 

the applicable directives. The declaration of con

-

formity can be read at the company‘s premises 

and will be sent to you upon request. This declaration certi

-

fies that the product complies with the mentioned directives, 

but does not represent any guarantee of the product‘s featu-

res. This declaration loses its validity, if the product is modi

-

fied without seeking our prior authorisation.

6.  EC manufacturer‘s declaration 

( distributor)

The installer is responsible for the proper assembly or com

-

missioning, the preparation of the declaration of conformity in 

accordance with EU directives and for affixing the CE mar

-

king. The CE marking must be affixed visibly!

Summary of Contents for PA-KL2 710











Reviews: