Simmons 701305-2282 Assembly Instructions Manual Download Page 18

Page: 18 / 20

Customer Service

Tel. (800) 377-3777

www.DeltaChildren.com

Locking/Unlocking Bassinet

• To lock the gliding mechanism, rotate the red lock arm clock wise and

snap the lock arm onto the lock peg.

NOTE:

There is a lock on both sides of the bassinet.

HINT:

Locks are located on opposite corners of the bassinet frame.

• Repeat lock procedure on other side of the bassinet.

• To unlock the gliding mechanism rotate the red lock arm counter clock

wise and off the lock peg.

NOTE:

Remember to unlock both sides of the bassinet.

Lock Arm

LOCKED

UNLOCKED

Lock Peg

NOTE:

when placing or lifting a child into or out of the bassinet make

sure the canopy is fully rotated into the closed position and electronic
mobile arm is fully rotated away from the baby.

• Fit the mobile to the mobile arm. Push the mobile up firmly.

HINT:

To disassemble the mobile for storage, press the tab on the

mobile arm and pull the mobile down.

Summary of Contents for 701305-2282





















Search results

Summary of Contents for 701305-2282

Reviews:

Related manuals for 701305-2282

Brands by name

Popular brands

Simmons 701305-2282, Assembly Instructions Manual

Search results

Summary of Contents for 701305-2282

Reviews:

Related manuals for 701305-2282

Brands by name

Popular brands