Simmons 701305-2282 Assembly Instructions Manual Download Page 10 | Manualshive

Page: 10 / 20

background image

10

Customer Service

Tel. (800) 377-3777

www.DeltaChildren.com

1

Mattress Support Board Assembly

Front of

mattress

board

FRONT

BACK

Mattress Support

Board

Mattress Board

Power Housing

Plastic Mattress

Board Support Nuts

Back of

mattress

board

*CORRECT PLACEMENT OF MATTRESS SUPPORT BOARD*

• Locate the mattress board, four (x4) M6 X 1.7cm screws, and a Phillips

screwdriver.

• Place the mattress board with the front and back labels facing the correct

way - into the frame lining up the four holes with the plastic mattress board
support nuts.

• Using a Phillips screwdriver and four (x4) M6 x 1.7cm screws, tighten the

mattress board onto the plastic mattress board supports nuts.

M6 Screw - 1.7cm - x4 - Actual Size

Top View Of Bassinet Frame

FRONT

BACK

TOP

&

FRONT

FRONT

Mattress Support

Board Fully Attached

To Bassinet Frame

«
...
8
9
10
11
12
...
»

Summary of Contents for 701305-2282





















Reviews:

No comments

Related manuals for 701305-2282

Brand: Halo Pages: 8

Brand: KayserBetten Pages: 48

Brand: Uberhaus Pages: 6

Brand: Munire Pages: 11

deluxe gliding stand

Brand: mothercare Pages: 23

Viaggio 2-3 Shuttle

Brand: Peg-Perego Pages: 124

SUN COMFORT RUSTICO

Brand: Glatz Pages: 12

Brand: Tobi Kindermöbel Pages: 3

Brand: Rookie Pages: 7

Brand: CB2 Pages: 4

Brand: CB2 Pages: 8

Brand: Bebe style Pages: 8

Brand: Bebe Stars Pages: 12

mamaRoo sleep bassinet

Brand: 4MOMS Pages: 53

Brand: Habitat Pages: 12

ingenuity FoldAway Rocking Bassinet-Wood 11162

Brand: Kids II Pages: 16

ingenuity FoldAway Rocking Bassinet 11659

Brand: Kids II Pages: 20

Disney Baby 60578-ES

Brand: Kids II Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands