Simmons 701305-2282 Assembly Instructions Manual Download Page 5 | Manualshive

Page: 5 / 20

background image

5

Customer Service

Tel. (800) 377-3777

www.DeltaChildren.com

Bottom Base Assembly

1

2

3

• Locate the two (x2) support tubes, and the fabric storage liner.
• Slide the support tubes into fabric storage liner on both sides.
• Flip over the fabric storage liner with support tubes, facing upward.

• Insert the back base leg into fabric storage liner.

M6 Screw - 1.7cm - x2 - Actual Size

Fabric Storage Liner

Back Base Leg

Fabric Storage

Liner

Slide Support Tube Into

Fabric Storage Liner

Fabric Storage

Liner Facing

Upward

• Locate the two (x2) M6 x 1.7cm screws, the back base leg, and a

Phillips screwdriver.

•

Align the bottom holes of the back base leg with the support tubes.

• Insert the (x2) M6 screws on both sides of the back base leg and

use a Phillips screwdriver to tighten both screws on both sides.

Support Tube

«
...
3
4
5
6
7
...
»

Summary of Contents for 701305-2282





















Reviews:

No comments

Related manuals for 701305-2282

Brand: Costway Pages: 7

Brand: PHI VILLA Pages: 10

Brand: KidKraft Pages: 10

Brand: Gami Pages: 40

Viaggio 2-3 Shuttle

Brand: Peg-Perego Pages: 124

Brand: Macdonald Pages: 4

Brand: Regalo Pages: 40

Baby & Junior Bed

Brand: sebra Pages: 40

Brand: Simmons Pages: 16

Brand: Mocka Pages: 4

Brand: Kiddicare Pages: 8

Anna Dropside Cot

Brand: Kiddicare Pages: 4

Brand: Kiddicare Pages: 20

Brand: Fisher-Price Pages: 6

Brand: Fisher-Price Pages: 20

Brand: Fisher-Price Pages: 16

Brand: Fisher-Price Pages: 20

Deluxe Auto Rock 'n Play CHN19

Brand: Fisher-Price Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands