Simex STI-94, User Manual

Page: 44 / 52

User manual - RATEMETER STI-94
Register Write Range Register description
78h Yes 0 ÷ 1
“ H r4 ” parameter in “ HOLd ” menu (the control mode of relay R4 and
LED R4) :
0 - control depends on current measurement values;
1 - control depends on peaks (or drops) values;
79h Yes 0 ÷ 1
“ HOUt ” parameter in “ HOLd ” menu ( the control mode of current
output):
0 - control depends on current measurement values;
1 - control depends on peaks (or drops) values;
A0h 2
Yes 0 ÷ 3
“ OUtmod ” parameter in “ OUtPUt ” menu (active current output mode)
0 - current output disabled ; 1 - current output enabled with 4 ÷ 20mA
mode; 2 - current output enabled with 0÷20mA mode ;
3 - current output controlled via RS-485 interface
Yes 0 ÷ 2
“
OUtmod
” parameter in “
OUtPUt
” menu (passive current output
mode)
0 - current output disabled ; 1 - current output enabled with 4 ÷ 20mA
mode; 2 - current output controlled via RS-485 interface
Yes 0 ÷ 5
“ OUtmod ” parameter in “ OUtPUt ” menu (active voltege output
mode)
0 - voltage output disabled ; 1 - voltage output enabled with 0 ÷5V
mode; 2 - voltage output enabled with 1÷5V mode ; 3 - voltage output
enabled with 0÷10V mode ; 4 - voltage output enabled with 2÷10V
mode ; 5 - voltage output controlled via RS-485 interface
A1h 2
A2h 2
Yes 0 ÷ 999999
“ OUt LO ” parameter in “ OUtPUt ” menu, no decimal point included
A3h 2
A4h 2
Yes 0 ÷ 999999
“ OUt HI ” parameter in “ OUtPUt ” menu, no decimal point included
A5h
2
Yes 0 ÷ 999
“ Lo r ” parameter in “ OUtPUt ” menu, for active current output and
active voltage output, expressed in 0.1%
Yes 0 ÷ 299
“ Lo r ” parameter in “ OUtPUt ” menu for passive current output,
expressed in 0.1%
A6h 2
Yes 0 ÷ 199
“ Hi r ” parameter in “ OUtPUt ” menu for active and passive current
output, expressed in 0.1%
Yes 0 ÷ 99
“
Hi r
” parameter in “
OUtPUt
” menu for active voltage output,
expressed in 0.1%
A7h 2
Yes 0 ÷ 3
“ AL ” parameter in “ OUtPUt ” menu (active current output value on
critical exception): 0 - no change; 1 - 22.1 mA; 2 - 3.4 mA; 3 - 0 mA
Yes 0 ÷ 2
“ AL ” parameter in “ OUtPUt ” menu (passive current output value on
critical exception): 0 - no change; 1 - 22.1 mA; 2 - 3.4 mA
Yes 0 ÷ 5
“ AL ” parameter in “ OUtPUt ” menu (active voltage output value on
critical exception): 0 - no change; 1 - 11 V; 2 - 5.5; 3 - 1.2 V;
4 - 0.6 V; 5 - 0 V
D8h Yes 0 ÷ 1
“
F or P
” parameter in
“inPUt”
menu (kind of value visible on the
display):
0
- frequency;
1
- period
1 - it is recommended to read these registers simultaneously – in 2-registers frames. If single registers are read, data
errors are possible because of changes of read value between successive registers readings.
44