Simex SRT-N118, User Manual

Page: 36 / 44

User manual - METER SRT-N118
Register Write Range Register description
01h No -999 ÷ 6000 Measurement value (no decimal point)
02h No 0h, A0h, 60h
The status of the current measurement; 0h - data valid; A0h - top
border of the measurement range is exceeded; 60h - bottom border
of the measurement range is exceeded;
03h No 1 Decimal point position, constant value: 1 - “ 0.0 ”;
04h Yes see descr.
State of the relays and alarm LED (binary format)
(1 - on, 0 - off):
00000000 000e00ba
a - relay R1; b - relay R2; e - alarm LED;
If written, only a , b bits are important (others are ignored) these bits
allows user to control the relays via RS-485 interface
05h 1
Yes 0h ÷ 1800h
State of active current output, expressed in 1/256 mA units – it
means that high byte express integer part, and low byte fractional
part of desired output current.
Yes 2CCh÷1800h
State of passive current output, expressed in 1/256 mA units – it
means that high byte express integer part, and low byte fractional
part of desired output current.
Yes 0h ÷ 1600h
State of active voltage output, expressed in 1/512 V units – it means
that high byte express integer part, and low byte fractional part of
desired output voltage.
06h No -999 ÷ 6000 Peak (drop) value (no decimal point)
10h Yes 0 ÷ 2
“ tyPE ” parameter in “ InPt ” menu (input type).
0 - Pt-100; 1 - Pt-500; 2 - Pt-1000
12h Yes 0 ÷ 5 “ FiLt ” parameter in “ InPt ” menu (measurement filtering rate)
18h Yes -99 ÷ 99
“ toFS ” parameter in “ InPt ” menu (shift of measurement scale),
expressed by 0,1°C
20h 2 Yes 0 ÷ 199 Device address
21h No 21B0h Device identification code (ID)
22h 3 Yes 0 ÷ 7
“bAud” parameter in “rS” menu (baud rate);
0 - 1200 baud; 1 - 2400 baud; 2 - 4800 baud; 3 - 9600 baud;
4 - 19200 baud; 5 - 38400 baud; 6 - 57600 baud; 7 - 115200 baud
23h
4
Yes 0 ÷ 1
“mbAc” parameter in “rS” menu (permission to write registers via
RS-485 interface); 0 - write denied ; 1 - write allowed
24h Yes see descr.
Parameters of “ SECU ” menu (binary format (0 - „ oFF ”, 1 - „ on ”):
bit 0 - “ A r1 ” parameter; bit 1 - “ A r2 ” parameter
25h Yes 0 ÷ 5
“rESP” parameter in “rS” menu (additional response delay);
0 - no additional delay; 1 - ” 10c ” option; 2 - ” 20c ” option;
3
- ”
50c
” option;
4
- ”
100c
” option;
5
- ”
200c
” option;
27h Yes 0 ÷ 99
“mbtO” parameter in “rS” menu (maximum delay between
received frames); 0 - no delay checking;
1 ÷ 99 - maximum delay expressed in seconds
2Dh Yes 1 ÷ 8
“ bri ” parameter (display brightness);
1 - the lowest brightness; 8 - the highest brightness
36