Simex SRT-N118, User Manual

Page: 37 / 44

User manual - METER SRT-N118
Register Write Range Register description
2Fh Yes 0 ÷ 1
“ Edit ” parameter (numerical parameters edit mode);
0 - „ dig ” mode; 1 - „ SLid ” mode
30h Yes -999 ÷ 9999 “
SEtP ” parameter in “ rEL1 ” menu, no decimal point included
31h Yes -999 ÷ 999 “ HySt ” parameter in “ rEL1 ” menu, no decimal point included
32h Yes 0 ÷ 5
“ modE ” parameter in “ rEL1 ” menu:
0 - “ noAC ” mode; 1 - “ on ” mode; 2 - “ oFF ” mode; 3 - “ in ” mode;
4 - “ out ” mode; 5 - “ modb ” mode
33h Yes 0 ÷ 999
“t on” parameter in “rEL1” menu, expressed in tenth of seconds or
tenth of minutes depend on “unit” parameter - register no. 35h)
34h Yes 0 ÷ 999
“toFF” parameter in “rEL1” menu, expressed in tenth of seconds
or tenth of minutes depend on “unit” parameter - register no. 35h)
35h Yes 0 ÷ 1
“unit”
parameter in
“rEL1”
menu:
0
- seconds;
1
- minutes
36h Yes 0 ÷ 2 “AL” parameter in “rEL1” menu: 0 - no changes; 1 - on; 2 - off
37h Yes -999 ÷ 9999 “ SEt2 ” parameter in “ rEL1 ” menu, no decimal point included
38h Yes -999 ÷ 9999 “ SEtP
” parameter in “
rEL2
” menu, no decimal point included
39h Yes -999 ÷ 999 “ HySt ” parameter in “ rEL2 ” menu, no decimal point included
3Ah Yes 0 ÷ 5
“ modE ” parameter in “ rEL2 ” menu:
0 - “ noAC ” mode; 1 - “ on ” mode; 2 - “ oFF ” mode; 3 - “ in ” mode;
4 - “ out ” mode; 5 - “ modb ” mode
3Bh Yes 0 ÷ 999
“t on” parameter in “rEL2” menu, expressed in tenth of seconds or
tenth of minutes depend on “unit” parameter - register no. 3Dh)
3Ch Yes 0 ÷ 999
“toFF” parameter in “rEL2” menu, expressed in tenth of seconds
or tenth of minutes depend on “unit” parameter - register no. 3Dh)
3Dh Yes 0 ÷ 1
“unit” parameter in “rEL2” menu:
0
- seconds;
1
- minutes
3Eh Yes 0 ÷ 2 “AL” parameter in “rEL2” menu: 0 - no changes; 1 - on; 2 - off
3Fh Yes -999 ÷ 9999 “ SEt2 ” parameter in “ rEL2 ” menu, no decimal point included
50h Yes 0 ÷ 1
“
modE
” parameter in “
HOLd
” menu (type of detected changes):
0
- peaks;
1
- drops
51h Yes 0 ÷ 9999
“ PEA ” parameter in “ HOLd ” menu (minimum detectable change, no
decimal point included)
52h Yes 0 ÷ 199
“ timE ” parameter in “ HOLd ” menu, maximum peaks' (or drops')
display time expressed in seconds
53h Yes 0 ÷ 1
“
HdiS
” parameter in “
HOLd
” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
54h Yes 0 ÷ 1
“ H r1 ” parameter in “ HOLd ” menu :
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
55h Yes 0 ÷ 1
“ H r2 ” parameter in “ HOLd ” menu:
0 - “ rEAL ” mode ; 1 - “ HOLd ” mode
37