Simex SRL-49, User Manual

Page: 52 / 62

User manual - METER SRL-49
Register Write Range Register description
A2h 1 Yes -999 ÷ 9999 “ OUtH ” parameter in “ OUtP ” menu, no decimal point included
A3h 1 Yes 0 ÷ 999
“
Lo r
” parameter in “
OUtP
” menu, expressed in 0.1%
A4h 1 Yes 0 ÷ 199 “ Hi r ” parameter in “ OUtP ” menu, expressed in 0.1%
A5h 1 Yes 0 ÷ 3
“ AL ” parameter in “ OUtP ” menu (current output value on critical
exception): 0 - no change; 1 - 22.1 mA; 2 - 3.4 mA; 3 - 0 mA
B0h Yes 0 ÷ 1
Parameter“ tyPE ” of sub-menu “ bAr ” (display mode of the
bargraph), 0 - line; 1 - point
B1h Yes 0 ÷ 6
Parameter “ FCol” of sub-menu “ bAr ” (colours of the bargraph)
0 - bargraph off; 1 - option “ grEE ”; 2 - option “ rEd ”;
3 - option “ g r ”; 4 -option “ r g ”; 5 - option “ b g ”; 6 - option “ b r ”
B2h Yes -999 ÷ 9999 Parameter “ Lo C ” of sub-menu “ bAr ”, no decimal point
B3h Yes -999 ÷ 9999 Parameter “ Hi C ” of sub-menu “ bAr ”, no decimal point
B4h Yes 0 ÷ 3
Parameter “ Pr1P ” of sub-menu “ bAr ” (relay's R1 thresholds'
markers): 0 – not showed; 1 - option ” 1St ”; 2 - option ” 2nd ”;
3 - option ” botH ”;
B5h Yes 0 ÷ 3
Parameter “
Pr2P
” of sub-menu “
bAr
” (relay's R2 thresholds'
markers): 0 – not showed; 1 - option ” 1St ”; 2 - option ” 2nd ”;
3
- option ”
botH
”;
B6h Yes 0 ÷ 3
Parameter “ Pr3P ” of sub-menu “ bAr ” (relay's R3 thresholds'
markers): 0 – not showed; 1 - option ” 1St ”; 2 - option ” 2nd ”;
3 - option ” botH ”;
B7h Yes 0 ÷ 3
Parameter “ Pr4P ” of sub-menu “ bAr ” (relay's R4 thresholds'
markers): 0 – not showed; 1 - option ” 1St ”; 2 - option ” 2nd ”;
3 - option ” botH ”;
B8h Yes 0 ÷ 4
Parameter “ P1AL ” of sub-menu “ bAr ” (critical situation defined for
relay R1): 0 - no change; 1 - option “ morE ”; 2 - option “ LESS ”;
3 - option “ on ”; 4 - option “ oFF ”
B9h Yes 0 ÷ 4
Parameter “ P2AL ” of sub-menu “ bAr ” (critical situation defined for
relay R2): 0 - no change; 1 - option “ morE ”; 2 - option “ LESS ”;
3 - option “ on ”; 4 - option “ oFF ”
BAh Yes 0 ÷ 4
Parameter “
P3AL
” of sub-menu “
bAr
” (critical situation defined for
relay R3): 0 - no change; 1 - option “ morE ”; 2 - option “ LESS ”;
3
- option “
on
”;
4
- option “
oFF
”
BBh Yes 0 ÷ 4
Parameter “ P4AL ” of sub-menu “ bAr ” (critical situation defined for
relay R4): 0 - no change; 1 - option “ morE ”; 2 - option “ LESS ”;
3 - option “ on ”; 4 - option “ oFF ”
1 - these registers are active only if device is equipped with active current output
2 - after writing to register no 20h the device responds with an “old” address in the message.
3 - after writing to register no 22h the device responds with the new baud rate.
4 - the value of the “ mbAc ” parameter is also connected to write to this register, so it is possible to block a writes, but
impossible to unblock writes via RS-485 interface, The unblocking of the writes is possible from menu level only.
5 - the pairs of „ X - Y ” coordinates may be defined for any free point. The pair is “free” (it means that particular point is
not defined) if „ X ” coordinate of this point is equal 8000h. After writing both X and Y coordinate the point is defined
and used in calculation of result. The coordinates of any point can be changed at any time.
52