Simex PUR-49D, User Manual

Page: 64 / 80

User manual - CONTROLLER PUR-49D
Register Write Range Register description
10h Yes 0 ÷ 20
“ tyPE ” parameter in “ InPt ” menu (nominal input range):
0 - 0-20 mA range; 1 - 4-20 mA range; 2 - 0-5 V range;
3 - 1-5 V range; 4 - 0-10 V range; 5 - 2-10 V range;
6 - 0-60 mV range; 7 - 0-75 mV range; 8 - 0-100 mV range;
9 - 0-150 mV range; 10 - Pt-100; 11 - Pt-500; 12 - Pt-1000
13 - thermocouple input K; 14 - thermocouple input S;
15 - thermocouple input J; 16 - thermocouple input T;
17 - thermocouple input N; 18 - thermocouple input R;
19 - thermocouple input B; 20 - thermocouple input E;
11h Yes 0 ÷ 3
“ CHAr ” parameter in “ InPt ” menu (characteristic type)
0 - linear ; 1 - square; 2 - square root; 3 - user defined
12h Yes 0 ÷ 255 “ FiLt ” parameter in “ InPt ” menu (time constant in seconds)
13h Yes 0 ÷ 3
“ Pnt ”parameter in “ InPt ” menu (the copy of 03h register, decimal
point position): 0 - “ 0 ”; 1 - “ 0.0 ”; 2 - “ 0.00 ”; 3 - “ 0.000 ”
14h Yes -999 ÷ 9999 “ Lo C ” parameter in “ InPt ” menu, no decimal point included
15h Yes -999 ÷ 9999 “ Hi C ” parameter in “ InPt ” menu, no decimal point included
16h Yes 0 ÷ 999 “ Lo r ” parameter in “ InPt ” menu, in 0.1%
17h Yes 0 ÷ 199 “ Hi r ” parameter in “ InPt ” menu, in 0.1%
18h Yes -99 ÷ 99
“ toFS ” parameter in “ InPt ” menu (shift of measurement scale),
expressed by 0.1°C (for RTD input) or by 1.0°C (for TC input)
19h Yes 0 ÷ 2
“ Conn ” parameter in “ InPt ” menu (RTD input connection method):
0 - “ 4 in ”; 1 - “ 3 in ”; 2 - “ 2 in ”
20h 2 Yes 0 ÷ 199 Device address
21h No 23DBh Device identification code (ID)
22h 3 Yes 0 ÷ 7
“bAud” parameter in “rS” menu (baud rate);
0 - 1200 baud; 1 - 2400 baud; 2 - 4800 baud; 3 - 9600 baud;
4 - 19200 baud; 5 - 38400 baud; 6 - 57600 baud; 7 - 115200 baud
23h 4 Yes 0 ÷ 1
“mbAc” parameter in “rS” menu (permission to write registers via
RS-485 interface); 0 - write denied ; 1 - write allowed
24h Yes see descr.
Parameters of “ SECU ” menu (binary format (0 - „ oFF ”, 1 - „ on ”):
bit 0 - “ A r1 ” parameter; bit 1 - “ A r2 ” parameter
bit 2 - “ A r3 ” parameter; bit 3 - “ A r4 ” parameter; bit 4 - “ A Pid ”
parameter;
25h Yes 0 ÷ 5
“rESP” parameter in “rS” menu (additional response delay);
0 - no additional delay; 1 - ” 10c ” option; 2 - ” 20c ” option;
3 - ” 50c ” option; 4 - ” 100c ” option; 5 - ” 200c ” option;
27h Yes 0 ÷ 99
“mbtO” parameter in “rS” menu (maximum delay between
received frames); 0 - no delay checking;
1 ÷ 99 - maximum delay expressed in seconds
28h Yes 0 ÷ 1 “ AL ” parameter in “ bEEP ” menu: 0 - off; 1 - on
29h Yes 0 ÷ 1 “ R1 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
2Ah Yes 0 ÷ 1 “ R2 ” parameter in “ bEEP ” menu: 0 - off; 1 - on
64