background image

140

IT

ES

FR

BE

GB

RUS

RO

If the rooms remain unused for a long period of time, the temperatu-

re can be reduced with the on-line key, in this way saving energy. When

the rooms are occupied again, press the on-line key to re-heat them.

The current choice is displayed on the display:

On-line key

Fixed temperature heating

Reduced temperature heating

NOTE:

In automatic mode, the apparatus switches from the fixed temperature to the reduced tem-

perature according to the time programme. The manual switching of the temperature is done

manually with the on-line key.

Temperature regulation

Fixed temperature: 

temperature when the rooms are occupied 

(basic setting) 

Reduced temperature: 

temperature during periods of absence or night

Hot-water service temperature:

– desired temperature of hot-water service

– comfort temperature of the hot-water service 

(with storage capacity boiler unit)

Reduced temperature of hot-water service (with storage capacity boiler unit):

temperature desired for hot-water service at reduced level.

To have access to the “reduced hot-water service temperature” parameter, press

the 

and 

keys at the same time for at least 5 seconds and then go along

the entered lines with the key 

until parameter 61 is reached. Regulate the value

with and 

.

Before proceeding with the adjustment  in the temperature on the regulator, the thermosta-

tic valves, which may be present, have to be regulated to the desired temperature.

1

2

3

61

PROGRAMMING

To enter the programming mode the flap on the control must be open.

As soon as the cover is open,

the display and the key functions

are switched on.

The number in the square

represents the programme

lines that may selected with the

arrow keys. 

You can set or display the following values:

• Temperatures

up to 

• Heating programme

up to 

• Day of the week and hour

up to 

• Current values                 

up to 

• Vacation period                                 

• Return to the default values                

1

3

4

1 1

12

14

15

1 7

18

19

If the control is in the manual mode 

, If the control is in the automatic mode  

the

control will revert automatically at the next change of the heating programme.

Programme line

Value

Value adjustment keys

Programme line selector

Summary of Contents for PLANET DEWY 100





























Reviews: