background image

1

Item

Part Number

Description

Quantity

GS-254G1120

Simalfa G11 | HVLP Spray Gun 2.0mm

01, 02, 03, 04

G11-01-04-2.0

Simalfa G11 | Air Cap 2.0mm

05

G11-05-2.0

Simalfa G11 | Fluid Nozzle 2.0 mm

06

G11-06

Simalfa G11 | Needle Packing Teflon

07

G11-07

Simalfa G11 | Needle Packing Nut

08

G11-08

Simalfa G11 | Air Valve Shaft

09

G11-09

Simalfa G11 | O-Ring (9x1) - [Included on Brass Air Valve Body Set]

10

G11-10

Simalfa G11 | O-Ring (10.6x1.65) - [Included on Brass Air Valve Body Set]

11

G11-11

Simalfa G11 | Brass Air Valve Body Set

12

G11-12

Simalfa G11 | Air Valve

13

G11-13

Simalfa G11 | Spring For Valve

14

G11-14

Simalfa G11 | O-Ring (8x1.5) - [Included on Fluid Needle Guide]

15

G11-15

Simalfa G11 | Fluid Needle Guide

16

G11-16-2.0

Simalfa G11 | Fluid Needle 2.0 mm

17

G11-17

Simalfa G11 | Fluid Needle Spring

18

G11-18

Simalfa G11 | Plastic Packing

19

G11-19

Simalfa G11 | Fluid Adjustment Knob

20

G11-20

Simalfa G11 | Pattern Adjustment Valve Set

21

G11-21

Simalfa G11 | Air Adjusting Valve Set

22

G11-22

Simalfa G11 | Air Hose Joint

23

G11-23

Simalfa G11 | Fluid Nipple

24

G11-24

Simalfa G11 | Trigger

25

G11-25

Simalfa G11 | Trigger Pin

26

G11-26

Simalfa G11 | Trigger Washer

27

G11-27

Simalfa G11 | Trigger Locking Ring

31

G11-31

Simalfa G11 | Needle Packing Washer

32

G11-32

Simalfa G11 | Needle Packing Spring

G11-06-07-31-32

Simalfa G11 | Needle Packing Kit (06, 07, 31, 32)

* Not sold separately at this time.

D E S C R I P C I Ó N   D E   P A R T E S   +   P R E C I O S

Packing (7, 32, 6, 31)

Summary of Contents for G11 HVLP















Reviews: