PL
46
Konserwacja
OSTRZEŻENIE
: Przed przeprowadzeniem kontroli, czynności konserwacyjnych lub czyszczenia
ZAWSZE odłączaj urządzenie od źródła zasilania.
Konserwacja skrzyni biegów
Patrz Rys. VI
Po każdych 6 godzinach użytkowania (w przybliżeniu) skrzynia biegów musi zostać ponownie
nasmarowana
1. Za pomocą klucza sześciokątnego zdejmij obudowę skrzyni biegów (4)
2. Do smarowania przekładni użyj szpatułki lub podobnego przyrządu w celu wypełnienia
zagłębienia (maks. 80 g)
Uwaga
: Uważaj, aby nie zarysować lub w inny sposób nie uszkodzić wewnętrznego mechanizmu
przekładni
3. Przymocuj ponownie osłonę skrzyni biegów
• Do narzędzia dołączono pojemnik smaru (12). Przy zakupie dodatkowego smaru należy wybrać
dowolne środek litowy smarujący
• Nie należy nadmiernie dokręcać pokrywy skrzyni biegów ani przepełniać przekładni smarem
Kontrola rutynowa
• Regularnie sprawdzaj, czy wszystkie śruby mocujące są odpowiednio dokręcone. Wibracje mogą
powodować ich poluzowanie.
• Sprawdź przewód zasilania urządzenia pod kątem uszkodzeń i zużycia za każdym razem przed
rozpoczęciem użytkowania urządzenia. Zalecenie to dotyczy również przewodów zasilania
wykorzystywanych przy urządzeniu.
Czyszczenie
• Należy zawsze dbać o czystość urządzenia. Brud i kurz powodują szybsze zużycie elementów
wewnętrznych i skracają okres eksploatacji urządzenia. Należy czyścić korpus urządzenia
miękką szczotką lub suchą ścierką. Jeśli to możliwe, przedmuchaj otwory wentylacyjne czystym
powietrzem sprężonym.
• Obudowę narzędzia czyścić miękką, wilgotną ściereczką z łagodnym detergentem. Nie używaj
alkoholu, benzyny ani silnych środków czyszczących
• Nigdy nie używaj środków żrących do czyszczenia części plastikowych
Smarowanie
Regularnie smaruj wszystkie elementy ruchome urządzenia odpowiednim środkiem smarnym w
aerozolu, wszystkie poza skrzynią biegów, która wymaga smaru litowego
Szczotki
• Wraz z upływem czasu szczotki węglowe wewnątrz silnika mogą się zużywać.
• Nadmiernie zużyte szczotki mogą prowadzić do utraty mocy, okresowych usterek lub pojawienia
się iskier.
• Wymiana szczotek: zdejmij osłonę otworów wentylacyjnych (10) i pokrywę dostępu do szczotek
(8). Zużyte szczotki można następnie wyjąć i wymienić na nowe
• Zawsze wymieniaj zużyte szczotki parami
• Zamontuj ponownie osłony
• Alternatywnie, należy oddać narzędzie do naprawy w autoryzowanym centrum serwisowym
Silverline
Kontakt
W celu uzyskania porady technicznej lub naprawy, skontaktuj się z infolinią pod numerem (+44)
1935 382 222
Strona online:
silverlinetools.com/en-GB/Support
Adres:
Powerbox
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Przechowywanie
• Należy przechowywać narzędzie w bezpiecznym, suchym miejscu niedostępnym dla dzieci.
Utylizacja
Należy zawsze przestrzegać przepisów krajowych dotyczących utylizacji elektronarzędzi, które nie są
już funkcjonalne i nie nadają się do naprawy.
• Nie wyrzucaj elektronarzędzi lub innych odpadów elektrycznych i elektronicznych (WEEE) wraz z
odpadami komunalnymi.
• Skontaktuj się z władzami lokalnymi zajmującymi się utylizacją odpadów, aby uzyskać informacje
na temat prawidłowego sposobu utylizacji elektronarzędzi.
Problem
Prawdopodobna przyczyna
Rozwiązanie
Podczas wiercenia rdzeniowego, wiertło zostało zablokowane/
utknęło w materiale
Nadmierny nacisk na narzędzie w momencie przełamania
materiału
Zmniejsz nacisk nakładany na urządzenie przed przełamaniem
materiału
Wiertło rdzeniowe nie jest odpowiednie do danego rodzaju
wiercenia
Użyj kompatybilnego wiertła rdzeniowego
Nagromadzona podczas pracy duża ilość zanieczyszczeń
wewnątrz wiertła rdzeniowego
Regularnie opróżniaj nagromadzone zanieczyszczenia, co
zapewni bezpieczne działanie
Narzędzie nie chce się uruchomić
Przepalony bezpiecznik
Sprawdź i dokonaj wymiany bezpiecznika. Jeżeli problem nie
ustaje należy skontaktować się z autoryzowanym centrum
serwisowym.
Uszkodzony kabel zasilania
Skontaktuj się z autoryzowanym centrum serwisowym
Uszkodzony przełącznik ON/OFF
Uszkodzony silnik
Niska prędkość obrotowa
Narzędzie zostało przergrzane
Wyłącz urządzenie i pozwól mu się schłodzić do temperatury
pokojowej. Sprawdź i wyczyść otwory wentylacyjne.
Powolna prędkość obrotowa lub brak obrotów oraz możliwe
widoczne iskrzenie od otworów wentylacyjnych
Zużyte szczotki węglowe
Wymień szczotki lub skontaktuj się z autoryzowanym centrum
serwisowym, w celu wymiany szczotek
Wibracje lub nadmierny hałas
Mało smaru w przekładni
Dodaj lub wymień smar
Nadmiernie zużyte wewnętrzne części ruchome
Skontaktuj się z autoryzowanym centrum serwisowym
Rozwiązywanie problemów
268819_Manual.indd 46
02/01/2018 09:54