Silverline 282400 Manual Download

Page: 9 / 52

Air Framing Nailer 90mm

282400

silverlinetools.com

WARNING:

The vibration emission during actual use of the power tool can differ from the

declared total value depending on the ways in which the tool is used. There is the need to identify

safety measures to protect the operator that are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to the trigger time) .

Carefully read and understand this manual and any label attached to the tool before use. Keep these

instructions with the product for future reference. Ensure all persons who use this product are fully

acquainted with this manual .

Even when used as prescribed it is not possible to eliminate all residual risk factors. Use with

caution. If you are at all unsure of the correct and safe manner in which to use this tool, do not

attempt to use it .

General Safety

a) For multiple hazards, read and understand the safety instructions before installing, operating,

repairing, maintaining, changing accessories on, or working near this tool . Failure to do so can

result in serious bodily injury

b) Only qualified and trained operators should install, adjust, or use this tool
c) Do not modify this tool. Modifications can reduce the effectiveness of safety measures and

increase the risks to the operator

d)  Do not discard the safety instructions; give them to the operator
e)  Do not use this tool if it has been damaged
f)  Tools shall be inspected periodically to verify that the ratings and markings required by this part

of ISO 11148 are legibly marked on the tool. The employer/user should contact the manufacturer

to obtain replacement marking labels when necessary

WARNING:

This appliance is not intended for use by persons (including children) with reduced,

physical or mental capabilities or lack of experience or knowledge unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children must be supervised to ensure that they do not play with the appliance.

Projectile Hazards

a) Be aware that failure of the workpiece or accessories, or even of the inserted tool itself, can

generate high-velocity projectiles

b) Always wear impact-resistant eye protection during operation of this tool. The grade of protection

required should be assessed for each use

c)  For overhead work, wear a safety helmet
d)  The risks to others should also be assessed at this time
e)  Ensure that the workpiece is securely fixed

Entanglement Hazards

• Choking, scalping and/or lacerations can occur if loose clothing, personal jewellery, neck wear,

hair or gloves are not kept away from the tool and its accessories

Operating Hazards

a)  Use of the tool can expose the operator’s hands to hazards, including cuts, abrasions and heat
b)  Wear suitable gloves to protect hands
c)  Operators and maintenance personnel should be physically able to handle the bulk, weight and

power of the tool

d) Hold the tool correctly; be ready to counteract normal or sudden movements and have both

hands available

e)  Maintain a balanced body position and secure footing
f)  Release the start-and-stop device in the case of an interruption of the energy supply
g)  Use only lubricants recommended by the manufacturer
h)  Personal protective safety glasses should be used; suitable gloves and protective clothing are

recommended

i) Avoid direct contact with moving parts in order to prevent pinching or cutting of hands or other

body parts

j) Wear suitable gloves to protect hands
k) There is a risk of electrostatic discharge if used on plastic and other non-conductive materials

Repetitive Motions Hazards

a) When using this tool to perform work-related activities, the operator can experience discomfort in

the hands, arms, shoulders, neck or other parts of the body

b) While using this tool, the operator should adopt a comfortable posture whilst maintaining secure

footing and avoiding awkward or off-balance postures . The operator should change posture

during extended tasks; this can help avoid discomfort and fatigue

c) If the operator experiences symptoms such as persistent or recurring discomfort, pain, throbbing,

aching, tingling, numbness, burning sensations or stiffness, these warning signs should not be

ignored. The operator should inform the employer and consult a qualified health professional

Accessory Hazards

a) Disconnect the tool from the energy supply before fitting or changing the inserted tool or

accessory

b) Avoid direct contact with the inserted tool during and after use, as it can be hot or sharp
c) Use only sizes and types of accessories and consumables that are recommended by the

manufacturer of this tool; do not use other types or sizes of accessories or consumables

Workplace Hazards

a) Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfaces caused by

use of the tool and also of trip hazards caused by the air line or hydraulic hose

b) This tool is not intended for use in potentially explosive atmospheres and is not insulated against

contact with electric power

Dust & Fume Hazards

a) Dust and fumes generated when using this tool can cause ill health (for example cancer, birth

defects, asthma and/or dermatitis); risk assessment and implementation of appropriate controls

for these hazards are essential

b) Risk assessment should include dust created by the use of the tool and the potential for

disturbing existing dust

c)  Direct the exhaust so as to minimise disturbance of dust in a dust-filled environment
d)  Where dust or fumes are created, the priority should be to control them at the point of emission
e)  Select, maintain and replace the consumable/inserted tool as recommended in the instruction

handbook, to prevent an unnecessary increase in dust or fumes

f) Use respiratory protection in accordance with employer's instructions and as required by

occupational health and safety regulations

Noise Hazards

a) Exposure to high noise levels can cause permanent, disabling hearing loss and other problems,

such as tinnitus (ringing, buzzing, whistling or humming in the ears). Therefore, risk assessment

and implementation of appropriate controls for these hazards are essential

b) Appropriate controls to reduce the risk can include actions such as damping materials to prevent

workpieces from ‘ringing’

c) Use hearing protection in accordance with employer's instructions and as required by

occupational health and safety regulations

d) Operate and maintain this tool as recommended in the instruction handbook, to prevent an

unnecessary increase in the noise level

e) Select, maintain and replace the consumable/inserted tool as recommended in the instruction

handbook, to prevent an unnecessary increase in noise

f) If the tool has a silencer, always ensure it is in place and in good working order when the tool is

being operated

Vibration Hazards

a) Exposure to vibration can cause disabling damage to the nerves and blood supply of the hands

and arms

b) Wear warm clothing when working in cold conditions and keep your hands warm and dry
c) If you experience numbness, tingling, pain or whitening of the skin in your fingers or hands, stop

using the machine, inform your employer and consult a physician

d) Operate and maintain the sander or polisher as recommended in the instruction handbook, to

prevent an unnecessary increase in vibration levels

e) Hold the tool with a light but safe grip, taking account of the required hand reaction forces,

because the risk from vibration is generally greater when the grip force is higher

Specific Safety

Important safety devices! Ensure correct function, maintain in accordance with instructions and

DO NOT disable!

Additional safety for air nailers & staplers

WARNING

Avoid unintentional firing.

Keep fingers away from trigger when not driving fasteners