6
GB
5. How to use
• Remove all packing material.
• Check to ensure that all parts are pre-
sent and undamaged.
•
Clean the device prior to its first
use!
(see “Cleaning” on page 7)
• Place the device on a dry, level, non-slip
surface.
6. Operation
DANGER! Risk of electric shock!
Only plug the mains plug
6
into the
wall socket when the Smoothie Blend-
er is completely assembled.
DANGER! Risk of injury from
cutting!
• Under no circumstances should the de-
vice be operated without the blender
jug
5
.
• The blades of the blade assembly
3
are
sharp. Handle it with care.
• The blades of the blade assembly carry
on rotating after the device has been
switched off. Wait until the blades have
come to a standstill before you remove
the blender jug.
WARNING!
In order to prevent damage to
the device, interrupt the blending process
immediately if the blades of the blade as-
sembly
3
rotate with difficulty or not at all.
In this case, pull out the mains plug
6
and
check whether there is an obstruction in the
blender jug
5
.
Application area
The Smoothie Blender is intended solely for
blending of whole fruit drinks (smoothies).
Preparing food
WARNING! Risk of material damage!
Thick or firm peels, (e.g. of citrus fruits, pine-
apple), stems and pips of stone fruits (e.g.
cherries, peaches, apricots) must be removed
before blending.
• Rinse or wash the fruits.
• Cut the fruit into rough pieces (approx.
3-4 cm edge length).
• Please use a sufficient amount of liquid
(mineral water, fruit juice, milk, yoghurt).
We recommend a mixing ratio of 1:1.
Blending
CAUTION:
depending on the hardness
and consistency of the ingredients in the
blender jug
5
, do not fill it to the maximum;
otherwise the blade assembly
3
could be-
come clogged.
NOTE:
if the smoothie is too thick, add a lit-
tle mineral water, fruit juice, milk or yoghurt
to suit your taste.
1. Place the fruit pieces and other ingredi-
ents into the blender jug
5
as desired.
2.
Figure C:
stick the blender jug into the
preassembled blade assembly
3
from
the bottom. The marking
8
points to-
wards the opened lock
4
. The locking
blades
9
on the blender jug engage
into the recess at the blade insert.
3. Turn the blender jug as far as it will go in
a clockwise direction, until the marking
8
points to the closed lock
4
.
4. Connect the mains plug
6
with the wall
socket.
5.
Figure A:
pivot the blender jug with
the motor unit
1
into its maximum up-
ward position. The blending process is
started.
6.
Figure B:
after approx. 10 - 20sec-
onds, pivot the blender jug with the motor
unit into its fully downwards position. The
blending process is thereby completed.
__RP86511_B4.book Seite 6 Montag, 9. Dezember 2013 10:14 10
Summary of Contents for SSM 175 A1
