manualshive.com logo in svg

Silicon Graphics VBOB, Owner'S Manual, Page: 26 / 40

Share
Download
Silicon Graphics VBOB Owner'S Manual Download Page 26

12

007-4243-002

3: VBOB Chassis Connectors and Cabling

Table 3-1 lists the VBOB connectors and their functions.

Table 3-1

Rear Panel Connectors

ID #

Connector Name

Connector Function

1.

AC plug and switch

AC power connection from chassis to power source

2.

 8-pin round

General purpose I/O connector #1 (reserved for future use)

3.

 8-pin round

General purpose I/O connector #2 (reserved for future use)

4.

9-pin subminiature D

RS-422 serial port A (reserved for future use)

5.

9-pin subminiature D

RS-422 serial port D (reserved for future use)

6.

9-pin subminiature D

RS-422 serial port C (reserved for future use)

7.

9-pin subminiature D

RS-422 serial port B (reserved for future use)

8.

SD in BNC #1

Standard Definition in #1 (link A)

9.

SD in BNC #2

Standard Definition in #2 (link B)

10.

9-pin subminiature D

RS-232 service port

11.

SD out BNC #1

Standard Definition out #1 (link A)

12.

SD out BNC #1

Standard Definition out #1 (link A)

13.

SD out BNC #2

Standard Definition out #2 (link B)

14.

SD out BNC #2

Standard Definition out #2 (link B)

15.

SD Genlock BNC

Standard Definition Genlock in BNC

16.

SD Genlock BNC

Standard Definition Genlock loop-through

17.

Timing BNC

Timing Out (to Genlock in on DG5-2 with TVO)

18.

HD out BNC #1

High Definition out BNC #1 (link A)

19.

HD out BNC #1

High Definition out BNC #1 (link A)

20.

HD out BNC #2

High Definition out BNC #2 (link B)

21.

HD out BNC #2

High Definition out BNC #2 (link B)

22.

HD Genlock BNC

High Definition Genlock in BNC

23.

HD Genlock BNC

High Definition Genlock loop-through

Summary of Contents for VBOB









































Reviews:

No comments