Silicon Graphics SGI Altix 450 User Manual Download | Manualshive

Page: 173 / 198

background image

SGI Electronic Support

007-4857-002

151

The sequence of events can be described as follows:

1.

Embedded Support Partner (ESP) monitors your system 24 hours a day.

2.

When a specified system event is detected, ESP notifies SGI via e-mail (plain text or

encrypted).

3.

Applications that are running at SGI analyze the information, determine whether a support

case should be opened, and open a case if necessary. You and SGI support engineers are
contacted (via pager or e-mail) with the case ID and problem description.

4.

SGI Knowledgebase searches thousands of tested solutions for possible fixes to the problem.

Solutions that are located in SGI Knowledgebase are attached to the service case.

5.

You and the SGI support engineers can view and manage the case by using Supportfolio

Online as well as search for additional solutions or schedule maintenance.

6.

Implement the solution.

Most of these actions occur automatically, and you may receive solutions to problems before they
affect system availability. You also may be able to return your system to service sooner if it is out
of service.

In addition to the event monitoring and problem reporting, SGI Electronic Support monitors both
system configuration (to help with asset management) and system availability and performance
(to help with capacity planning).

«
...
171
172
173
174
175
...
»

Summary of Contents for SGI Altix 450







































































































































































































Reviews:

No comments

Related manuals for SGI Altix 450

RayTech RNS 5.0

Brand: Raymarine Pages: 152

Work.Group/Windows 3

Brand: Amanda Pages: 106

Brand: MACROMEDIA Pages: 830

FreeAgent Desk 2TB

Brand: Seagate Pages: 2

Doctor Pro TM-2430-13

Brand: A&D Pages: 69

Digital Cameras

Brand: Nikon Pages: 51

ENTERPRISE LINUX 4.5.0 -

Brand: Red Hat Pages: 434

Enterprise Manager

Brand: Oracle Pages: 38

BREEZE 5-MANAGER

Brand: MACROMEDIA Pages: 306

COLDFUSION 4.5-DEVELOPING WEB

Brand: MACROMEDIA Pages: 380

SECURITY - FOR PDA 5.0

Brand: KAPERSKY Pages: 153

Brand: GRASS VALLEY Pages: 2

Brand: ACD Systems Pages: 232

MultiRack SoundGrid V9.5

Brand: Waves Pages: 35

SCAN TO PC DESKTOP 10

Brand: Xerox Pages: 4

Brand: Fellowes Pages: 170

Brand: HP Pages: 23

Insight Dynamics 6.2

Brand: HP Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands