Silicon Graphics GDM-4011P, Service Manual

Page: 8 / 43

13
Getting Started Customizing Your Monitor
F
EN
ES
C
4
Press the > ? / / buttons to adjust the settings.
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the
button again.
To reset, press the
?
(reset) button while the OSD is on.
The selected item is reset to the factory setting.
For
H CONVERGENCE
V CONVERGENCE
TOP
V CONVER TOP
BOT
V CONVER BOTTOM
CANCEL MOIRE
ADJ
MOIRE ADJUST
Press
/ . . . to shift red shadows to the right
and blue shadows to the left
?
. . . to shift red shadows to the left
and blue shadows to the right
/ . . . to shift red shadows up and blue
shadows down
? . . . to shift red shadows down and
blue shadows up
/ . . . to shift red shadows up and blue
shadows down
? . . . to shift red shadows down and
blue shadows up
/ . . . to shift red shadows up and blue
shadows down
? . . . to shift red shadows down and
blue shadows up
/ . . . to turn CANCEL MOIRE “ON”
? . . . to turn CANCEL MOIRE “OFF”
/ . . . to increase the moire cancellation
effect
? . . . to decrease the moire cancellation
effect
ON OFF
ON OFF
50
0
Using the OPTION On-screen
Display
The OPTION OSD allows you to manually degauss the
screen and adjust settings such as the OSD position and
power saving delay time. It also allows you to lock the
controls.
Degaussing the screen
The monitor screen is automatically degaussed
(demagnetized) when the power is turned on.
You can also manually degauss the monitor.
1
Press the button.
The MENU OSD appears.
2
Press the ¨ . / > and > ? / / buttons to select “
OPTION,” and press the button again.
The OPTION OSD appears.
3
Press the ¨ . / > buttons to select “ (MANUAL
DEGAUSS).”
4
Press the > / button.
The screen is degaussed for about 2 seconds.
If you need to degauss the screen a second time, wait for at
least 20 minutes before repeating the steps above.
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the
button again.
ON
MANUAL DEGAUSS
UNLOCK
1 MIN
OPTION
ZZ...
14
Customizing Your Monitor
Setting the power saving delay time
You can set the delay time before the monitor enters the
power saving mode. See page 17 for more information on
this monitor’s power saving capabilities.
1
Press the button.
The MENU OSD appears.
2
Press the ¨ . / > and > ? / / buttons to select “
OPTION,” and press the button again.
The OPTION OSD appears.
3
Press the ¨ . / > buttons to select “ ZZ... (PWR SAVE
DELAY).”
4
Press the > ? / / buttons to select the desired time.
When PWR SAVE DELAY is set to “OFF,” the monitor
does not go into power saving mode.
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the
button again.
To reset, press the ? (reset) button while the OSD is on.
ON
MANUAL DEGAUSS
UNLOCK
1 MIN
OPTION
ZZ...
Changing the on-screen display position
You can change the OSD position (for example, when you
want to adjust the picture behind the OSD).
1
Press the button.
The MENU OSD appears.
2
Press the ¨ . / > and > ? / / buttons to select “
OPTION,” and press the button again.
The OPTION OSD appears.
3
Press the ¨ . / > buttons to select “ (OSD H
POSITION)” or “ (OSD V POSITION).”
Select “ (OSD H POSITION)” to adjust the horizontal
position.
Select “ (OSD V POSITION)” to adjust the vertical
position.
4
Press the > ? / / buttons to move the OSD to the
desired position.
The OPTION OSD automatically disappears after about 30
seconds.
To close the OSD, press the
button again.
To reset, press the
?
(reset) button while the OSD is on.
ON
MANUAL DEGAUSS
UNLOCK
1 MIN
OPTION
ZZ...
ZZ...
OSD H POSITION
UNLOCK
1 MIN
OPTION
ZZ...
OSD V POSITION
UNLOCK
OPTION
1
ZZ...
PWR SAVE DELAY
OPTION
5 SEC
60 MIN 1 MIN
OFF
1
1-4