Silca Twister 2 Operating Manual Download Page 23

Page: 23 / 26

Operating manual - English

Twister II

Copyright Silca S.p.A. 2017

8.4

REPLACING THE JAWS ON RIGHT-HAND CLAMP

Fig. 23

Make sure the motor ON switch is OFF

8.4.1

REPLACING LEFT JAW

1)  Unscrew the knob (E1).
2)  Loosen the 2 screws  (B2) and remove the jaw.
3)  Fit the new jaw up against the left-hand side and align also

from the front.

4)  Tighten the 2 screws (B2) without exerting pressure.
5)  Screw in the knob (E1).
6)  Fully tighten the screws  (B2).

Fig. 24

8.4.2

REPLACING RIGHT JAW

1)  Unscrew the knob (E1).
2)  Loosen the 2 screws  (B3) and remove the jaw.
3)  Fit the new jaw up against the right-hand side and align

also from the front.

4)  Tighten the 2 screws (B3) without exerting pressure.
5)  Screw in the knob (E1).
6)  Fully tighten the screws  (B3).

Fig. 25

Summary of Contents for Twister 2



























Search results

Summary of Contents for Twister 2

Reviews:

Related manuals for Twister 2

Brands by name

Popular brands

Silca Twister 2, Operating Manual

Search results

Summary of Contents for Twister 2

Reviews:

Related manuals for Twister 2

Brands by name

Popular brands