Silca TARGA 2000 Operating Manual Download Page 24 | Manualshive

Page: 24 / 26

background image

Operating manual - English

TARGA 2000

24

Copyright Silca 1999

9

ASSISTANCE

Silca provides full assistance to purchasers of the TARGA 2000 key-cutting machine.
To ensure complete safety for the operator, any job not specified in this manual should be carried
out by the manufacturer or in the special Service Centres recommended by Silca.
On the back cover of this manual is a list of the manufacturer’s addresses; listed below are the
addresses of specialised Service Centres.

9.1

How to request service

The guarantee attached to TARGA 2000 key-cutting machines ensures free repairs or
replacements of faulty parts within 12 months of purchase. All other service calls must be arranged
by the customer with Silca or with a Silca service centre.

«
...
22
23
24
25
26
»

Summary of Contents for TARGA 2000



























Reviews:

No comments

Related manuals for TARGA 2000

Brand: JB Systems Pages: 7

Brand: 3B SCIENTIFIC PHYSICS Pages: 36

Brand: 3A HEALTH CARE Pages: 16

Short/cut 2000 Audio Editor

Brand: 360 Systems Pages: 4

Brand: ACE INSTRUMENTS Pages: 15

Brand: Wave Fitness Pages: 15

Brand: Federal Signal Corporation Pages: 4

Brand: FASTERHOLT Pages: 96

Brand: Panta Safe Light Pages: 2

Brand: Calrec Pages: 70

Brand: Jaga Pages: 32

Brand: Mach Pages: 12

Brand: Sable Pages: 28

Brand: JBM Pages: 12

Brand: ABB Pages: 154

Brand: WAGNER Pages: 31

Brand: Hameg Pages: 39

Brand: Teac Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands