Silca MARKER 2000 Operating Manual Download Page 41 | Manualshive

Page: 41 / 58

background image

Operating manual - English

MARKER 2000

Copyright Silca 2002

37

9.4

Removing the upper cover

To gain access to some parts of the machine for

maintenance purposes (e.g. belt tension-replacement,

display replacement) the top cover (Q) must be removed.

Proceed as follows.
1) turn off the machine and remove the plug.
2) remove the four screws (Q1) securing the cover to

the machine.

3) slightly raise the rear of the cover and very carefully

pull forward, releasing it from the front catches (fig.

33).

4) disconnect the connector (B1) and faston (B2) from

the display.

Fig. 32

Fig. 33

Q

Q1

B1

B2

«
...
39
40
41
42
43
...
»

Summary of Contents for MARKER 2000



























































Reviews:

No comments

Related manuals for MARKER 2000

Brand: parktool Pages: 2

Brand: Datavideo Pages: 8

Brand: Wacker Neuson Pages: 48

Brand: Parkside Pages: 99

Strong-Arm CLL500

Brand: Clarke Pages: 8

Brand: EIBENSTOCK Pages: 24

Brand: Rockwell Pages: 24

PSI 9000 Series

Brand: Electro-Automatik Pages: 64

Brand: Kett Pages: 6

Brand: Campbell Hausfeld Pages: 16

Brand: Eaton Pages: 6

Brand: Image Industries Pages: 32

Brand: G.SKILL Pages: 2

Brand: MAIMAN ELECTRONICS Pages: 24

Brand: Radio Shack Pages: 13

Brand: Campbell Hausfeld Pages: 10

750-613/040-000

Brand: WAGO Pages: 52

Brand: Timberline Tool Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands