background image

VO 

Operation and handling  

Technical changes reserved 

 

- 53 -

 

6.3.9

 

Pulse outputs (level 24 and 25) (only displays 2 and 3) 

6.3.9.1

 

Original pulses 

Irrespective of the operating mode, only the pulses which reach pulse input “A” are output as 
original pulses. The pulse duration for original pulses is always 4 ms and cannot be altered. 
6.3.9.2

 

Scaled pulses  

Depending on the volume/quantity of mass, pulses can be output at the pulse output. A pulse is 
always followed by a pulse-pause of identical duration (Ratio 1:1). 
The following pulse durations can be selected in level 25: 

Pulse duration [ms] 

12 

24 

48 

100 

Max. output frequency [Hz] 

125 

42 

21 

10 

 

Select the type of pulse output in level 24:: 

0: Original pulses 
1-6: Scaled pulses 
OFF: No pulse output 

Pulses are not lost. If the max. output frequency is briefly exceeded due to an excessive flow 
rate, the pulses are metered in a “pulse buffer”. This buffer outputs the remaining pulses 
once the flow rate has been reduced. 
The display (V1) is used to determine the scaling. 
Definition of the positions for the following explanations: 
Position 1 = far right, Position 2 = second from right, etc. 

 

Example 1: 
Setting “1” has been selected in level 24 (= position 1): 
Meter reading (V1):  01357.246 kg 
If position 1 changes from 6 to 7, the pulse buffer increases by 1. 

 The pulse buffer increases by 1 every time position 1 changes. 

The pulses are output immediately. 
Example 2: 
Setting “4” has been selected in level 24 (= position 4): 
Meter reading (V1):  01357.246 m³ 
If position 4 changes from 7 to 8, the pulse buffer increases by 1. 

 The pulse buffer increases by 1 every time position 4 changes. 

Example 3: 
Setting “4” has been selected in level 24 (= position 4): 
The pulse buffer increases by 10 pulses if position 5 changes from 5 to 6, since this repre-
sents a 10 step change to position 4. The pulses are output immediately. 
Clever selection of the scaling factor (level 24) and the pulse duration (level 25) can help to 
achieve a high resolution without reaching the maximum output frequency of the meter. 

Caution: 
Subsequent changes to the number of digits after the decimal point for the volume can affect 
the output of the scaled pulses! The setting in level 24 must then be corrected. 

OFF 

Summary of Contents for VO 015



































Reviews: