background image

 

 

  SIKA, Dr. Siebert & Kühn GmbH & Co. KG, Struthweg 7-9, 34260 Kaufungen, Germany 

8/8   

Tel: +49-5605-803-0, Fax: +49-5605-803-54, email: [email protected], web: www.SIKA.net 

 

 

 

 

 

Specification 

Measuring ranges: 

Display range: 

-10.0 to 350.0 mbar relative (under pressure down to –350.0 mbar, p.r.t. chapter 5) 

Overload: 

max. 1000 mbar rel. (without destruction or recalibration of sensor being 

necessary) 

Resolution: 

0.1 mbar 

(

10 Pa) 

Pressure units: 

mbar, bar, kPa, MPa, mmHg, PSI mH

2

O (only for devices with ‚m‘ printed below 

display), selectable 

Accuracy: (typ.) 

±0,2%FS (hysteresis and linearity) 

±0,4%FS (temperature dependency 0-50°C) 

 

OPTION higher accuracy:  

±0.1%FS (hyst., lin.) 

 

 

 

 

 

±0.4%FS (temp. dep. 0-50°C) 

Measuring rate: 

4 meas./sec  

Nominal temperature:  25°C 

 

 

Sensor: 

Piezo-resistive relative pressure sensor integrated in device. Suitable for air and 

non-corrosive and non-ionizing gases and liquids. 

(Not suitable for water – use air buffering) 

Connection:  

2 metal pressure ports for connection to 6 x 1 mm tubes at the top of device (4mm 

inner tube Ø) 

 

Power-Off-Function:

   Device will be automatically switched off if no key is pressed/no interface 

communication takes place for the time of the power-off delay. The power-off delay 

can be set to values between 1 and 120 min.; it can be completely deactivated.  

 

Display

2 four digit LCDs (12.4mm high and 7 mm high) for measuring values, and for min/ 

max memories, hold function, etc. as well as additional functional arrows. 

 

Pushbuttons

:  

6 membrane keys 

 

Interface

Serial interface (3.5mm jack) can be connected to RS232 interface of a PC via 

electrically isolated interface adapter GRS3100 or GRS3105 (see accessories). 

 

Power supply

:  

9V battery, type: IEC 6F22  (included in scope of supply)  

as well as additional d.c.connector (diameter of internal pin 1.9 mm) for external 

10.5-12V direct voltage supply. (suitable power supply: GNG10/3000) 

Power consumption:  

Slow measuring rate: < 1.2 mA   

Low battery warning: 

!

-display and ' bAt ' 

 

Housing

:  

impact-resistant ABS, membrane keyboard, transparent panel, Front side IP65 

Dimensions:  

142 x 71 x 26 mm (L x W x D) + metal pressure ports 11mm at top of device 

Working temperature:  0...+50°C 

Allowable rel. humidity:  0...95 % r.H. (not condensing) 

Storage temperature:  -20...+70°C 

 

EMC

The MH3160-07 device corresponds to the essential protection ratings established 

in the Regulations of the Council for the Approximation of Legislation for the 

member countries regarding electromagnetic compatibility (89/336/EWG).  

Additional fault:  

<1%  

 

Summary of Contents for MH3160-07









Reviews: