Signature Kitchen Suite UPSXB2627S Service Manual Download

Page: 54 / 78

HOW TO DISASSEMBLE AND ASSEMBLE

1. Top Cover

2-1. Top Decor

2-3. Case Decor

2-4. PCB Cover

2-2. Machine Cover

1) Remove 2 screws located at upper side of top cover.

2) Be caution of hanger and remove the top cover upward.

1) Remove top cover

2) Remove the screw located on the edge of the cover.

1) Remove top cover

2) Remove 2 screws below and remove the Top Decor.

1) Remove top cover

2) Remove 2 screws below and remove the Decor case.

1) Remove the top cover

2) Remove the Top decor.

3) Remove the Case Decor.

4) Remove the ground.

3) Remove direction of red arrow.

5) After removing PCB Cover Screw, remove the cover.

CAUTION

- Deco case of the connecting lines are connected

to the sensor, so please carefully separated.

Hook

Summary of Contents for UPSXB2627S















































































Search results

Summary of Contents for UPSXB2627S

Reviews:

Related manuals for UPSXB2627S

Brands by name

Popular brands

Signature Kitchen Suite UPSXB2627S, Service Manual

Search results

Summary of Contents for UPSXB2627S

Reviews:

Related manuals for UPSXB2627S

Brands by name

Popular brands