SignaMax 065-7840 User Manual Download Page 53

Page: 53 / 228

Signamax 065-7840 24-Port 10/100/1000BaseT/TX Managed Switch

Fig. 3-8

Parameter description of Port 23 and Port24:

Connector Type:

Displays the connector type, for instance, UTP, SC, ST, LC and so
on.

Fiber Type:

Displays the fiber mode, for instance, Multimode, Singlemode.

Tx Central Wavelength:

Displays the fiber optical transmitting central wavelength, for
instance, 850nm, 1310nm, 1550nm and so on.

Baud Rate:

Displays the maximum baud rate of the fiber module supported, for
instance, 10M, 100M, 1G, 10G and so on.

Vendor OUI:

Displays the Manufacturer's OUI code which is assigned by IEEE.

Vendor Name:

Displays the company name of the module manufacturer.

Vendor P/N:

Displays the product name provided by the module manufacturer.

Vendor Rev (Revision):

Displays the module revision.

Summary of Contents for 065-7840





































































































































































































































Search results

Summary of Contents for 065-7840

Reviews:

Related manuals for 065-7840

Brands by name

Popular brands

SignaMax 065-7840, User Manual

Search results

Summary of Contents for 065-7840

Reviews:

Related manuals for 065-7840

Brands by name

Popular brands