SignaMax 065-7840 User Manual Download Page 123

Page: 123 / 228

Signamax 065-7840 24-Port 10/100/1000BaseT/TX Managed Switch

113

Function name:

802.1x Mode Setting

Function description:

Sets the operation mode of 802.1X for each port. In this device, it supports
only the Multihost operation mode.

Parameter description:

Port Number:

Indicates which port is selected to configure the 802.1x operation mode.

802.1x Mode:

802.1x operation mode. There are two options, Disable and Multihost
mode. Default is "Disable".

Disable

The chosen port acts as a plain port; that is, no 802.1x port access
control works on the port.

802.1x with Multi-host

In this mode, for the devices connected to this port, those devices can
access the network resource through this port once a supplicant is
authorized.

Fig. 3-53

Summary of Contents for 065-7840





































































































































































































































Search results

Summary of Contents for 065-7840

Reviews:

Related manuals for 065-7840

Brands by name

Popular brands

SignaMax 065-7840, User Manual

Search results

Summary of Contents for 065-7840

Reviews:

Related manuals for 065-7840

Brands by name

Popular brands