manualshive.com logo in svg

SignaMax 065-7840, User Manual

The SignaMax 065-7840 User Manual is available for free download at manualshive.com. This comprehensive manual provides detailed instructions and troubleshooting tips for effortless setup and optimal usage of the SignaMax 065-7840. Get all the information you need to make the most out of this exceptional product.

Share
Download
background image

Signamax 065-7840 24-Port 10/100/1000BaseT/TX Managed Switch 

96 

 

Forward Delay: 

The user can set the root bridge forward delay time. This figure is set 
only by the root bridge. The forward delay time is defined as the time 
spent from Listening state moved to Learning state, and also from 
Learning state moved to Forwarding state of a bridge port. The forward 
delay time contains two states: Listening state to Learning state, and 
Learning state to Forwarding state. It assumes that forward delay time is 
15 seconds, and then the total forward delay time will be 30 seconds. 
This has much to do with the STP convergent time which will be more 
than 30 seconds because of additional factors.  

The valid values are 4 ~ 30 seconds, default is 15 seconds. 

Force Version: 

Two options are offered for the STP algorithm. One is RSTP and the 
other is STP.  If STP is chosen, RSTP will run as a legacy STP. The 
switch supports RSTP (802.1w) which is backwards compatible with STP 
(802.1d). 

 

 

           Fig. 3-43

 

 

Summary of Contents for 065-7840





































































































































































































































Reviews:

No comments

Related manuals for 065-7840

3Com OfficeConnect 1600 Datasheet preview
OfficeConnect 1600
Brand: 3Com Pages: 8
3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
Cabletron Systems SmartSwitch Router User'S Reference Manual preview
SmartSwitch Router
Brand: Cabletron Systems Pages: 338
Patton electronics 2888 Quick Start Manual preview
2888
Brand: Patton electronics Pages: 8
N-Tron 702-W User Manual & Installation Manual preview
702-W
Brand: N-Tron Pages: 62
IBM BladeCenter Management Module Installation And User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 184
Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Brand: Buffalo Pages: 71
TP-Link TL-SG2424P User Manual preview
TL-SG2424P
Brand: TP-Link Pages: 176
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Brand: Moxa Technologies Pages: 51
Avaya ERS 5510 Technical Configuration Manual preview
ERS 5510
Brand: Avaya Pages: 73
Solwise 3GWIFIMRD User Manual preview
3GWIFIMRD
Brand: Solwise Pages: 231
Microtek MiniLink Operation Manual preview
MiniLink
Brand: Microtek Pages: 25
Ubiquiti UniFi AP PRO Quick Start Manual preview
UniFi AP PRO
Brand: Ubiquiti Pages: 20
Milesight Pro UR32 Quick Start Manual preview
Pro UR32
Brand: Milesight Pages: 15
TRENDnet TE100S8P - Fast Ethernet Switch (Spanish) Quick Installation Manual preview
TE100S8P - Fast Ethernet Switch
Brand: TRENDnet Pages: 11
Rackable Systems OmniStor 4900F Series User Manual preview
OmniStor 4900F Series
Brand: Rackable Systems Pages: 196
PairGain HiGain Line Unit HLU-388 Quick Installation Manual preview
HiGain Line Unit HLU-388
Brand: PairGain Pages: 7
QSC Q-SYS QIO-GP8x8 Hardware User Manual preview
Q-SYS QIO-GP8x8
Brand: QSC Pages: 13

Brands by name

Popular brands

Load more brands