.
Additional Items Required ( Not Included in Kit)
Note: These are parts that we have used and are familiar with. There are many other brands
available and you may substitute other items that you are more comfortable with or have on
hand.
1 Engine
Norvel Big Mig .049 or Norvel Big Mig .061
4 Hinges
Sig Easy Hinges #SH-710 or Du-Bro Kwik Hinge #537
2 Collars
3/32" Wheel Collars Sig #SH-585 or Du-Bro #138
1 Control Horn
Sig #SH-220 or Du-Bro #107 (if using rudder control)
2 Aileron Push Rods
Wire Make From Sig #SH-133 or Du-Bro #229 or make
from 1/16" Music Wire
1 Collar
1/16" Wheel Collar Sig # SH-584 or Du-Bro #137
1 Motor
Mount Dave Brown #0506
4 Motor Mount Screws and Blind
Nuts
4-40x3/4" Machine Screws and Blind Nuts Sig #SH-111 or
Du-Bro #129
1 Servo Mount Tape
Sig #SH-119 or Du-Bro #634
1 Throttle Pushrod Assembly
Sig #SH-559 or Du-Bro #165 ( if using throttle control)
2 Wheels
Dave Brown LectraLite Wheels #5617 (13/4") or #5620
(2")
1 Tail Wheel
3/4" Sullivan Wheel #350
1 Fuel Tank
Sullivan loz. #SS-1 or 20z. #SS-2
1 1/2-A Fuel Line
Sig #SH-288 or Du-Bro #221
3 Servo Connectors
Sig #SH-736 or Du-Bro #121 (5 Reqd. if using Rudder and
Throttle)
1 Yellow Covering Material
1 Roll Top Flite Monokote, Cub Yellow #TOPQ0220
1 Black Covering Material
1 Roll Top Flite Monokote, Black #TOPQ0208
1 Yellow Paint
Top Flite LusterKote Cub Yellow #TOPR7220
1 Black Paint
Top Flite LusterKote Black #TOPR7208
1 Propeller
Grish Tornado 6-3 Nylon Propeller #GRIQ1050
6 Rubber Bands (wing attach)
Sig #SH-340
2 Wheel Bushings
Make from K & S Brass Tube #127
1 Nylon Reinforcing Tape
Goldberg #450
1 1 1/2" Spinner
Du-Bro #261
General Note: Cover the plans with wax paper before assembling your model to prevent the parts from sticking to the plan.
Building the Tail Surfaces
1.
Make the elevators by gluing parts E-2 to parts E-1 over the plan.
2.
Join the elevators using the 1/8" dowel using the plan and part S-1 as a guide. Trim the dowel as required to achieve the
proper length.
3.
Temporarily hinge the elevators to the stabilizer. Do not glue the hinges in place at this time. Sand the stabilizer smooth
and sand the edges round. Glue R-2 to the top of R-3 over the plan.
4.
If you are going to fly your model 2 or 3 channel (no rudder control) then glue the rudder assembly to R-1.
4a.
If you are building the model 4 channel, temporarily hinge the rudder to the fin. Do not glue the hinges in place at this time.
5.
Sand these parts smooth and sand all edges round except the bottom of part R-1.
6.
Remove the hinges from the tail surfaces and set these parts aside until needed later in construction.
Building the Fuselage
7.
Glue the doublers F-2 to the inside of the fuselage sides (F-1). Be sure to make one right and one left hand side.
8.
Glue the 3/32" x 1/4" to the top and bottom of F-6 as shown on the plan.
9.
Position formers F-3 and F-4 on one fuselage side and glue them into position making sure that they are 90 degrees to the
fuselage side.