manualshive.com logo in svg

Sifos Technologies PowerSync PSA-PL, Installation Manual, Page: 6 / 20

Share
Download
Sifos Technologies PowerSync PSA-PL Installation Manual Download Page 6

PSA Installation Guide

 

6 

 

PowerSync

 Analyzer Installation Guide  Copyright © 2007-2012 Sifos Technologies, Inc., All Rights Reserved 

Physical and Environmental Specifications 

 

PHYSICAL  

 

PSA-100 
 

Width:   

 

4.2 “ 

Height:   

 

1.65”  

 

Depth:   

 

9.15” (Including Rear-Panel Connectors) 

Weight:   

 

1.4 lbs. 

Power:   

 

5V, 700mA Max.  (100VAC – 240VAC, 50-60Hz Wall Plug-in Adaptor Supplied) 

 

PSA-1200, PSA2400 
 

Width:   

 

19 “ 

Height:   

 

5.25” (3 Rack-Unit)  

Depth:   

 

12” 

Weight:   

 

17.25 lbs.  (Fully Populated) 

Power:   

 

100VAC – 240VAC, 50-60Hz, 600mA Max. 

 

ENVIRONMENTAL  

 

Operating Temperature: 

50°C at 20W Max per Port, linearly de-rated from 30°C at 30W per port (see Graph) 

 

 

 

Note: 

30W is the heat dissipation rating, not the power loading capability of each PSA  

Test Port

. 

 

 

 
Storage Temperature: 

-20°C to 85°C 

Operating Humidity: 

5% to 95% RH, Non-Condensing. 

Summary of Contents for PowerSync PSA-PL





















Reviews:

No comments