Sierra NS-1N30-00 Manual Download Page 3

3

42445 Avenida Alvarado, Temecula, CA  92590

(800) 451-9343,  www.nimbuswater.com

Congratulations on your purchase of the Nimbus Sierra reverse osmosis system.  When properly maintained, this system will 

provide you with years of trouble-free service.   The next sections contain important information on proper care and mainte-

nance. Please take a few minutes to read through this information.

The cartridges in this system must be replaced on a regular basis to maintain  efficiency and to ensure high water quality.  

These cartridges work together and must be replaced every  6-12 months.  Any significant change in performance of the 

system should be investigated promptly to avoid secondary damage or deterioration to other parts of the system.

CAUTION: Improperly installed systems could result in water damage due to leaks or flooding.  Proper installation of this 

system requires familiarity with standard sink plumbing and proper use of common hand and power tools.  If you are not 

familiar with standard sink plumbing and proper use of common hand and power tools or have any difficulty with the 

installation of this system, consult a licensed professional, such as a contractor or plumber.  

NOTE:  This system has been designed for installation by licensed professionals, such as a contractor or plumber. 

Introduction To The Sierra

Stage

Description

Cap Color

Replacement 

Interval

1 & 2

20 micron sediment  

prefilter plus granular 

 

activated carbon.

Green

6-12 months

3

Reverse osmosis membrane

White

12 months

or when TDS  

rejection falls 

below 85%

4

Granular activated carbon 

post-filter

Blue

6-12 months

System Performance 

Daily production rate 

 

 

42.8 L/d (11.3 gpd)       

Total Dissolved Solids Reduction  

 

96.4% 

  

Feed Water Requirements

Feed Water  

 

 

Potable, municipal water

Feed Pressure 

 

 

40psi - 80psi

Feed temperature 

 

 

40°F to 100°F

Total dissolved solids  

 

 

2,000 mg/L max 

Chlorine 

 

 

<1.0 mg/L max. 

pH 

 

 

4-8

Turbidity 

 

 

<1.0 NTU

SDI 

 

 

<5

Iron, Manganese, Hydrogen Sulfide   

0 ppm 

  

Do not use with water that is microbiologically unsafe or of unknown quality without adequate  

disinfection before or after the system.

Summary of Contents for NS-1N30-00












Reviews: