Siemens SPCP432, Manual

Page: 3 / 18

Back tamper switch installation
The back tamper switch is available as an optional
extra (SPCY130).
Mounting the wall fixing plate
¾
Mount the SPC enclosure in the appropriate
position on the wall using all three fixings (see
Fig. 8 item 1).
¾
Draw a line around the inside of the back tamper
cutout (see Fig. 8 item 2) to provide a guide for
the wall plate on the fixing wall.
¾
Remove the enclosure from the wall.
¾
Place the wall plate (Fig 9, item 1) on the wall
centring it precisely around the rectangle
previously drawn (Fig. 9, item 2).
¾
Ensure all four flanges on the wall plate are
flush with the wall.
¾
Mark the four fixings on the wall plate.
¾
Drill and use suitable screws (max. 4 mm) for
the wall substrate.
¾
Fit the wall plate to the wall.
Fitting the back tamper switch
¾
Insert the tamper switch (Fig. 10 item 2) into the
back of the enclosure so that the plunger faces
outwards. (Fig. 10 item 1)
¾
Fit the enclosure back onto the wall using the
three fixings removed previously.
¾
Visually check to ensure there is a flush finish
between the wall plate and the enclosure
metalwork.
WARNING:
If thwall fixing plate is not accurately aligne
then the panel will not sit properly on its
fixings.
Wiring the back tamper switch
¾
Connect one end of the tamper leads to terminal
block CN4 (Fig.1 item 27).
¾
Plug the two connectors at the end of the
tamper leads onto the COM (common) and NO
(normally open) spade connectors on the back
tamper switch.
Appendix A: LED Status
Condition
Mains
green
Battery
green
Fuse
red
Limit
*
red
Status
green
Normal On On Off Off On
Mains OK,
battery charging
On Flash On
Mains fail,
battery OK
Off On On
Mains OK, and
battery not
installed or
faulty.
On Off On
Mains fail, and
battery not
installed, faulty
or in deep
discharge
protection mode
All LEDs off
Output 1 fuse
open Single
Flash
On
Output 2 fuse
open Double
Flash
On
Expander fuse
open Triple
Flash
On
More than one
fuse open
On On
Current exceeded
on any output
On On
PSU switcher
failure
Off Flash
Battery link
missing
All LEDs flash together
* Current limit
Appendix B: Battery link position
(Fig. 1 Item 8)
Link Description
DTX Do not use
17 A
h Select this option if a 17Ah battery is fitted to
the PSU
7 Ah
Select this option if a 7Ah battery is fitted to the
PSU
Note: Only one of the above links can be fitted to
this header.
Appendix C: Choosing the stand-by battery
The table below shows the maximum total current (in
mA) that can be drawn from all outputs for EN
compliance. Note that other limits apply, for example,
the maximum current that can be drawn from each of
outputs 1 and 2 is 750 mA.
Available current in mA =
1000 * (0.85 * battery capacity in Ah) / (standby time
in hours) - 77 mA
Battery capacity
7 Ah
(Grade 2)
17 Ah
(Grade 3)
Standby
Time
(hours)
12 419 1127
24 171 525
30 121 405
60 Not to be used 164
Appendix D: Fitting additional expanders in
the SPC hinged enclosure
The enclosure can accommodate:
•
1 Battery (17 Ah max.)
•
1 x PSU Expander (SPCP430)
•
3 x I/O Expanders (optional)
To access the expanders and the PSU, open the
front lid to view the hinged mounting bracket. The
boards are secured to the hinged mounting bracket
by four mounting pillars.
To access or install a PSU in this enclosure:
¾
With an appropriate screwdriver loosen (but do
not remove) the top two securing screws on the
mounting bracket.
¾
Gently push the mounting bracket in an upward
direction until the screws are free from contact
with the bracket.
¾
Slowly but firmly pull the mounting bracket out
until it rotates down and is secured by the
resting pins
¾
The underside of the mounting bracket and the
enclosure provides space for additional
expanders to be installed (secured by four
mounting pillars).
The PSU is secured to the front of the enclosure by
mounting pillars.
See Fig. 6: Mounted PSU
1 Battery
Please ensure that battery flaps are used to
hold the battery securely when mounted in the
cabinet.
See Fig. 7: Rotated views
1 Battery
2 Expanders
3 SPC controller or PSU
When installing the SPCP430 (PSU and
expander), ensure that the 4-pin cable is
securely attached to the connector on the
expander and to the PSU beneath.
Technical data
Power supply Type A (EN50131-1)
Mains voltage 230 V AC, +10 to -15 %, 50 Hz
Mains fuse
500 mA T (replacable part on mains
terminal block)
Power
consumption
Max. 220 mA at 230 V AC
Operating
Current Max. 124 mA at 12 V DC (all relays
activated)
Quiescent
Current
Max. 84 mA at 12 V DC
Output Voltage
11-14 V DC in normal conditions
(mains powered and fully charged
battery), min. 9.5 V DC when
powered by secondary device
(before system shut down to battery
deep discharge protection)
Low voltage
trigger
7.5 V DC
Over voltage
protection
15 V DC
Peak to Peak
ripple
Max. 5% of output voltage
Auxiliary power
(nominal) Max. 1500 mA at 12 V DC (750 mA
per output)
Battery type
SPCP432: YUASA NP7-12FR
(7 Ah)
SPCP433: YUASA NP17-12FR (17
Ah)
(battery not supplied with product)
Battery charger
SPCP432: 72h for 80 % of battery
capacity
SPCP433: 24h for 80 % of battery
capacity
Battery
protection
Current limited to 2 A (fuse
protected), deep discharge
protection at 10.5 V DC +/- 3 % (fault
at deep discharge v 0.5 V
DC)
Number of on-
board zones
4, for door release switch (DRS) and
door position switch (DPS), or freely
programmable
EOL resistor
Dual 4K7 (default), other resistor
combinations configurable
Number of card
readers
2
Number of on-
board relays
2, for door locks or freely
programmable (single-pole
changeover, 30 V DC / max. 1 A
resistive switching current)
Field bus X-BUS on RS-485 (307 kb/s)
Calibration
No calibration checks required
(calibrated at manufacturing)
Serviceable
parts
No serviceable parts available
Tamper contact
SPCP432: Front spring tamper,
SPCP433: Front spring tamper
Operating
temperature
0 to +40 °C
Relative
humidity
Max. 90 % (non-condensing)
Colour RAL 9003 (signal white)
Dimensions
(W x H x D)
SPCP432: 264 x 357 x 81 mm
SPCP433: 326 x 415 x 114 mm
Weight
SPCP432: 4.7 kg
SPCP433: 6.3 kg
Housing
SPCP432: Small metal housing
(>1.2 mm mild steel)
SPCP433: Hinged metal housing
(>1.2 mm mild steel)
Housing can
contain up to
SPCP433: 3 additional expanders
(size 150 x 82 mm)