manualshive.com logo in svg

Siemens Siwarex U, Device Manual

Share
Download
Siemens Siwarex U Device Manual Download Page 65

7BCOMMUNICATION IN SIMATIC S7 

 

8.7  Peripheral area for SFC, SFB, FB communication 

In simple applications where only the weight values and status information is to be 
read, the user can access the peripheral address of the SIWAREX module directly. 

The following table shows the assignment of the peripheral area when 
communication to "SFC, SFB, FB" is selected in the HW config. Byte "0" 
corresponds to the address of the SIWAREX U module in the HW config. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table 8-1 

Allocation of the peripheral area 

 

8.8  Peripheral area for I/O communication 

Communication via the peripheral area can be used when "I/O" communication has 
been selected in the HW config for the communication with external systems when 
using the peripheral system ET200 M. 

The details are described in a separate chapter (see Chapter 

9 Communication 

with other systems 

). 

 

 

 

 

 

 

Byte 

S7 output area  

S7 input area 

Channel 1

 

0 

Not used 

BYTE cyclic counter 

1 

Not used 

BYTE status 

2 Not 

used 

3 Not 

used 

INT gross weight 

4 Not 

used 

5 Not 

used 

WORD digital value from the 
ADC 

6 Not 

used 

7 Not 

used 

WORD operating faults - 
asynchronous errors 

Channel 2

 

8 

Not used 

BYTE cyclic counter 

9 

Not used 

BYTE status 

10 Not 

used 

11  

Not used 

INT gross weight 

12  

Not used 

13  

Not used 

WORD digital value from the 
ADC 

14  

Not used 

15  

Not used 

WORD operating faults - 
asynchronous errors 

SIWAREX U 

8-57

 

Summary of Contents for Siwarex U


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands