Siemens SIWAREX MS Device Manual Download Page 41

Page: 41 / 75

Weighing

Functions

5.7.2

DS 30 – Operating Errors

The byte displays the current operating errors.

Bit No.

Name

Comment

1= Reboot due to RAM error

See message list Chapter

7.6

1= Restart because of a watchdog error or program fault

See message list Chapter

7.6

1= No 24 V module voltage (can only be read in SIMATIC-
CPU, not with SIWATOOL MS)

See message list Chapter

7.6

1= Number overflow in weight calculation

See message list Chapter

7.6

1= Parameter error

See message list Chapter

7.6

1= AD converter at limit of measuring range

See message list Chapter

7.6

1= Minimum voltage undershot on sensor line

See message list Chapter

7.6

1= AD converter fault

See message list Chapter

7.6

Table 5-8

Operating error (Bit information)

5.7.3

DS 30 – Gross Process Value

The current gross weight value.

5.7.4

DS 30 – Net Process Value

The current net weight value.

5.7.5

DS 30 – Tare Process Value

The current tare weight value.

5.7.6

DS 30 – G/N Weight

The current weight value, which is shown in the scale’s main display (external
remote display, type Siebert S102 or ASCII).

5.7.7

DS 30 – G/N Weight_x10

The current weight value with a higher resolution, which can be displayed
temporarily in the main display (external remote display type Siebert S102 or
ASCII) for a duration of 5 seconds.

5.7.8

DS 30 – Tare

The current tare weight, in the resolution specified in the numeral step (DS3).

5.7.9

DS 30 – Unfiltered Raw Digit Value from AD Converter

The current digit value from the AD converter without digital signal filtering.

SIWAREX MS 5-33

Summary of Contents for SIWAREX MS












































































Search results

Summary of Contents for SIWAREX MS

Reviews:

Related manuals for SIWAREX MS

Brands by name

Popular brands

Siemens SIWAREX MS, Device Manual

Search results

Summary of Contents for SIWAREX MS

Reviews:

Related manuals for SIWAREX MS

Brands by name

Popular brands