manualshive.com logo in svg

Siemens SITRANS F C MASSFLO MASS 6000 Ex-d, Manual, Page: 10 / 32

Share
Download
Siemens SITRANS F C MASSFLO MASS 6000 Ex-d Manual Download Page 10

SITRANS F C MASSFLO

10

SFIDK.PS.028.Q1.02

3.  Electrical connection

3.1 Electrical connection

compact or remote

(continued)

Electrical connections are made through the front of the signal converter (view A), in the terminal
housing. This housing is accessed by removing the front cover described in chapter 2.

Read the chapter 4. "Technical data" before making the connection.

The cover is retained via a wire. The terminal housing is equipped with 1 M20 EEx e gland and 1
M20 EEX i gland.
The mains cable is fed through the black PG gland (black indicates increased safety "e") located
in the left-hand side as viewed from the front.
The outputs are fed through the blue PG gland (the colour blue indicates intrinsically-safe circuit "i")
located on the right-hand side. According to the Ex document issued, use of other glands is
permitted provided that these are as a minimum EEx-approved in category "e".

Important

The power supply terminals shall be from a safety isolating transformer.
Maximal cable core is 1.5   .

Turn off the power supply before connecting input and output cables and wait 30 minutes
before unscrewing the lid.

Summary of Contents for SITRANS F C MASSFLO MASS 6000 Ex-d

































Reviews:

No comments