Siemens SIMATIC S7 300 PLC Getting Started Download Page 34

Page: 34 / 84

Learning units

3.9 9. Step: Configuration of the SINAMICS drive with S7T Config

Sequence

Activity

Result

The SINAMICS

training case on which this document is based has two different motor types. One of the

two motor types has DRIVE-CLIQ technology. The second motor/encoder is connected via SMC20, which

is why DRIVE-CLiQ recognizes that a second motor/encoder is present and creates this, but cannot

automatically configure it. Therefore, not all drive information can be completely configured automatically.
Confirm the warning with "OK".

Close the "Automatic Configuration" dialog box by clicking "Close".

CPU 317T-2 DP: Controlling a SINAMICS S120

3-24

Getting Started, 12/2005, A5E00480391-01

Summary of Contents for SIMATIC S7 300 PLC





















































































Search results

Summary of Contents for SIMATIC S7 300 PLC

Reviews:

Related manuals for SIMATIC S7 300 PLC

Brands by name

Popular brands

Siemens SIMATIC S7 300 PLC, Getting Started

Search results

Summary of Contents for SIMATIC S7 300 PLC

Reviews:

Related manuals for SIMATIC S7 300 PLC

Brands by name

Popular brands