Siemens SENTRON PAC2200 Product Manual Download Page 92

Page: 92 / 130

Technical specifications

8.1 Technical specifications

PAC2200

Equipment Manual, 12/2019, L1V30415167B-03

Dimensions and weights

Type of fixing

Standard rail mounting TH35 to EN 60715

Construction type

6TE

Housing dimensions W x H x D

108 mm x 97 mm x 71 mm

[4.2 in x 3.8 in x 2.8 in]

Weight

5 A device without packaging

310 g

5 A device with packaging

375 g

65 A device without packaging

415 g

65 A device with packaging

480 g

Degree of protection and protection class

Protection class

Safety class II

Degree of protection according to IEC 60529

Front area

IP40

Termination area

IP20

If higher degree of protection requirements are placed on the application engineering, the

customer must take suitable measures. This includes installation in a protective enclosure

with degree of protection IP51 and higher

Environmental conditions

Operation is only permissible in a control cabinet or fuse box inside an enclosed dry room.

Environmental conditions
Temperature range

Ambient temperature during operating phase

-25 °C … +55 °C

(K55)

Ambient temperature during transport and storage

-25 °C … +70 °C

Relative humidity (annual average value)

< 75 % RH

Installation altitude above sea level

max. 2000 m

Degree of pollution

Environmental tests

according to
EN 60068-2-27
EN 60068-2-6
EN 60068-3-3

Summary of Contents for SENTRON PAC2200



































































































































Search results

Summary of Contents for SENTRON PAC2200

Reviews:

Siemens SENTRON PAC2200, Product Manual, Page: 92 / 130

Search results

Summary of Contents for SENTRON PAC2200

Reviews: