Siemens SENTRON PAC2200 Product Manual Download Page 10

Page: 10 / 130

Introduction

1.2 Latest information

PAC2200

Equipment Manual, 12/2019, L1V30415167B-03

General safety notes

DANGER

Hazardous voltage

Will cause death, serious personal injury, or equipment damage.
Turn off and lock out all power supplying this equipment before working on this device.

WARNING

Impairment of protection as a result of improper use.

Can cause death, serious personal injury, or equipment damage.
The device may be used only for the applications described in the catalog and the

associated technical documentation.

Note
These operating instructions do not purport to cover all details or variations in equipment, or

to provide for every possible contingency in connection with installation, operation, or

maintenance. Should additional information be desired, or should particular problems arise

that are not discussed in enough detail in the operating instructions, please contact

Technical Support (

https://www.siemens.com/lowvoltage/technical-support

) for the

information you require.

Safety-related symbols on the device

Symbol

Meaning

(1)

Danger of electric shock

(2)

General Warning Symbol

(3)

Electrical installation and maintenance by qualified personnel only

Summary of Contents for SENTRON PAC2200



































































































































Search results

Summary of Contents for SENTRON PAC2200

Reviews:

Siemens SENTRON PAC2200, Product Manual, Page: 10 / 130

Search results

Summary of Contents for SENTRON PAC2200

Reviews: