Siemens SCALANCE X101-1 Commissioning Manual Download Page 82

Page: 82 / 86

Glossary

Fault Mask

Definition of a desired status (good status); deviations from this status during operation are

considered as errors/faults.

Fiber optic

Monomode

The monomode fiber (also single-mode fiber) typically has a core diameter of 5 to 9

µm.

However, the outer diameter is also 125

µm. The actual transmission of the information takes

place in the core of the fiber.

Multicast

A frame with a multicast address is received by all recipients which are ready for receiving

this address.

Multimode

In multimode transmission, the pulse is transferred using many modes (waves) which travel

along curved paths or which are reflected within the core. Attenuation is mainly caused by

physical absorption and dispersion as well as by mechanical bending. Among other things,

the amount of attenuation depends on the wavelength of the input light. Multimode fiber-optic

cables have an outer diameter of 125 µm and a core diameter of 50 or 62.5 µm. Due to the

larger core diameter, the pulse edges degrade more than in single mode transmission, which

results in shorter transmission distances.

OSM

Optical Switching Module

–

SIMATIC NET Ethernet switch with optical ports.

Industrial Ethernet Media Converters SCALANCE X-100 Series

Glossary-2

Commissioning Manual, 07/2008, A2B00051521A

Summary of Contents for SCALANCE X101-1























































































Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands

Siemens SCALANCE X101-1, Commissioning Manual

Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands