Siemens SCALANCE X101-1 Commissioning Manual Download Page 72

Page: 72 / 86

Installation and Maintenance

5.4 Maintenance

Removing the IE FC RJ-45 plug 180

Unlatch the IE FC RJ-45 plug 180 by slightly pressing the latching to remove the plug.

Figure

5-6

Unlatching the RJ-45 plug

If, for lack of space, a manual unlatching is not possible, you can also unlatch the plug with a

2.5 mm screwdriver. Subsequently you can remove the IE FC RJ-45 plug 180 from the

twisted pair port.

5.4

Maintenance

The devices of the product lines SCALANCE X-100 and X-200 are equipped with a self-

resetting fuse (resettable fuse / PTC). If the fuse blows (all LEDs are off despite correctly

applied power supply), the device should be disconnected from the power supply for approx.

30 minutes before it can be turned on again.

If any different fault develops, please send the device to your SIEMENS service center for

repair. Repairs on-site are not possible.

Industrial Ethernet Media Converters SCALANCE X-100 Series

5-8

Commissioning Manual, 07/2008, A2B00051521A

Summary of Contents for SCALANCE X101-1























































































Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands

Siemens SCALANCE X101-1, Commissioning Manual

Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands