Siemens SCALANCE X101-1 Commissioning Manual Download Page 44

Page: 44 / 86

Product Characteristics

4.4 SCALANCE X101-1LD

Range

The maximum transmission range (segment length) is 26 km if the signal attenuation of the

FOC is ≤ 0.5

dB/km.

Connectors

The cables are connected to BFOC sockets.

4.4.6

SCALANCE X101-1LD Power Supply and Signaling Contact

Power Supply

The power supply is connected using a 4-pin plug-in terminal block. The power supply can

be connected redundantly. Both inputs are isolated. There is no distribution of load. When

using a redundant power supply, the power supply unit with the higher output voltage

supplies SCALANCE X101-1LD alone. The power supply is connected over a high

resistance with the enclosure to allow an ungrounded setup.

Figure 4-15

Power supply SCALANCE X101-1LD

Figure

4-16

Connector pinout

Pin number Pinout
Pin 1

L1+ (+18 - 32V DC)

Pin 2

M1 (ground)

Pin 1

M2 (ground)

Pin 2

L2+ (+18 - 32V DC)

Industrial Ethernet Media Converters SCALANCE X-100 Series

4-30

Commissioning Manual, 07/2008, A2B00051521A

Summary of Contents for SCALANCE X101-1























































































Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands

Siemens SCALANCE X101-1, Commissioning Manual

Search results

Summary of Contents for SCALANCE X101-1

Reviews:

Related manuals for SCALANCE X101-1

Brands by name

Popular brands