Siemens SCALANCE W788C-2 Operating Instructions Manual Download Page 5

Page: 5 / 50

SCALANCE W788C-2
Operating Instructions, 07/2019, A5E03692120-14

Introduction

1.1

Information on the Operating Instructions

Validity of the Operating Instructions

These operating instructions cover the following products:

Product

Article number

SCALANCE W788C-2 RJ-45

6GK5788-2FC00-1AA0

SCALANCE W788C-2 M12

6GK5788-2GD00-1AA0

SCALANCE W788C-2 M12 EEC

6GK5788-2GD00-1TA0

If information relates to all the named products, the term SCALANCE W7x8 will be used.
These operating instructions apply to the following software version:

●

SCALANCE W7x8C with firmware as of version 8.31

Purpose of the Operating Instructions

Using the Operating Instructions, you will be able to install and connect the SCALANCE

W7x8 correctly. The configuration and the integration of the device in a WLAN are not

described in these instructions.

Documentation on the accompanying CD

You will find introductory information about configuration in the document "Getting Started

SCALANCE WLC711" on the accompanying SIMATIC NET IWLAN CD under the file name:
GS_SCALANCE-WLC711_76 pdf

Note
Detection of the W788C-2 M12 EEC devices
When the W788C-2 M12 EEC devices are detected by the configuration software of the

WLC 711, they are shown as W788C-2 M12.

Note
Make sure that you read the explanations and instructions in the README.txt file

Summary of Contents for SCALANCE W788C-2



















































Search results

Summary of Contents for SCALANCE W788C-2

Reviews:

Related manuals for SCALANCE W788C-2

Brands by name

Popular brands

Siemens SCALANCE W788C-2, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE W788C-2

Reviews:

Related manuals for SCALANCE W788C-2

Brands by name

Popular brands