Siemens SCALANCE W788C-2 Operating Instructions Manual Download Page 20 | Manualshive

Page: 20 / 50

background image

Description

3.4 Accessories

SCALANCE W788C-2

20

Operating Instructions, 07/2019, A5E03692120-14

Type

Properties

Article number

ANT896-6MM

Omnidirectional antenna for mobile wireless,

WLAN and GPS, WLAN: 6/7 dBi, 2.4 GHz

and 5 GHz, IP68, IP69 K, QMA-Connect

female, port 2

6GK5896-6MM00-0AA0

IWLAN RCoax Cable

2,4 GHz PE 1/2"

Omni antenna, 0 dBi 2.400 - 2.485 GHz, N-

Connect female

6XV1875-2A

IWLAN RCoax Cable

5 GHz PE 1/2"

Omni antenna, 0 dBi 5.150 – 5.875 GHz, N-

Connect female

6XV1875-2D

NOTICE
ANT795-4MA
The ANT795-4MA antenna has degree of protection IP30 and is therefore only suitable for

dry environments.

Note
ANT793-8DJ
The antenna ANT793-8DJ may only be used with the flexible connecting cable 6XV1875-

5CH50 (5 m length) or 6XV1875-5CN10 (10 m length). Other flexible connecting cables are

not permitted.
Notice for USA/Canada
Only one antenna per device can be used (connected to R1A1, R1A2 or R2A1, R2A2).

Note
ANT793-8DK
The antenna ANT793-8DK may only be used with the flexible connecting cable 6XV1875-

5CN10 (10 m length). Other flexible connecting cables are not permitted.
Notice for USA/Canada
Only one antenna per device can be used (connected to R1A1, R1A2 or R2A1, R2A2).

«
...
18
19
20
21
22
...
»

Summary of Contents for SCALANCE W788C-2



















































Reviews:

No comments

Related manuals for SCALANCE W788C-2

Brand: Barco Pages: 6

Brand: Datavideo Pages: 17

Brand: Datamax Pages: 22

SIGMA CONTROL 2

Brand: KAESER KOMPRESSOREN Pages: 246

Brand: Parker Pages: 21

Brand: Parker Pages: 26

Brand: Parallax Pages: 3

Brand: WAREMA Pages: 112

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

Brand: Dantherm Pages: 20

Brand: Ultraflex Pages: 7

Brand: PESA Pages: 30

Cutler-Hammer Jockey

Brand: Eaton Pages: 12

Brand: IBM Pages: 214

Brand: STIEBEL ELTRON Pages: 44

Brand: National Instruments Pages: 22

Brand: D+H Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands