Siemens SCALANCE W788C-2 Operating Instructions Manual Download Page 12 | Manualshive

Page: 12 / 50

background image

Description

3.1 Description of the device

SCALANCE W788C-2

12

Operating Instructions, 07/2019, A5E03692120-14

SCALANCE W7x8x-x M12 - IP65 degree of protection

①

Connecting connectors, N-Connect type female

•

Devices with one IWLAN interface: 3 connectors on the top (covered in the figure).

•

Devices with two IWLAN interfaces: 3 connectors on the top and 3 on the underside.

②

LEDs

③

Connector for the supply voltage, type M12 (with cover)

④

Connector for Ethernet, M12 type (with cover)

⑤

Screw-down cover for the

- reset button and the

- PLUG compartment (not with W788C)

⑥

PLUG compartment (not with W788C)

⑦

Reset button (covered in the figure)

⑧

Grounding connector (thread M4) on the back of the device

Figure 3-2

SCALANCE W7x8 M12

«
...
10
11
12
13
14
...
»

Summary of Contents for SCALANCE W788C-2



















































Reviews:

No comments

Related manuals for SCALANCE W788C-2

Brand: ABB Pages: 63

Brand: Raymarine Pages: 12

Brand: Jafar Pages: 13

Brand: YOKOGAWA Pages: 2

ALICAT SCIENTIFIC PC

Brand: Halma Pages: 2

ALICAT SCIENTIFIC PCD

Brand: Halma Pages: 46

Brand: jablotron Pages: 2

Brand: tau Pages: 9

Brand: tau Pages: 8

Brand: York Pages: 24

Brand: V2 Pages: 12

NORA-W10 Series

Brand: u-blox Pages: 56

Brand: z21 Pages: 2

1E0671-1 MCR2.9

Brand: Haberl Electronic Pages: 9

Brand: J+J Pages: 2

Brand: Hattersley Pages: 2

Brand: National Instruments Pages: 6

Brand: TUYA Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands