Siemens SCALANCE W734-1 Operating Instructions Manual Download Page 22

Page: 22 / 64

Description of the device

3.5 LED display

SCALANCE W774-1 /W734-1

Operating Instructions, 01/2017, C79000-G8976-C325-08

3.5

LED display

Information on operating status and data transfer

On the front of the housing, several LEDs provide information on the operating status of the

device:

LED

Color

Meaning

Off

Power supply too low

Green

Power supply L1 is applied.

Off

Power supply too low

Green

Power supply L2 is applied.

PoE

Green

Power supply using Power over Ethernet.

Green

There is a connection via the first Ethernet interface (Link).

Green and yel-

low flashing

alternately

Data transfer via the first Ethernet interface.

Green

There is a connection via the second Ethernet interface (Link).

Green and yel-

low flashing

alternately

Data transfer via the second Ethernet interface.

Summary of Contents for SCALANCE W734-1

































































Search results

Summary of Contents for SCALANCE W734-1

Reviews:

Related manuals for SCALANCE W734-1

Brands by name

Popular brands

Siemens SCALANCE W734-1, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE W734-1

Reviews:

Related manuals for SCALANCE W734-1

Brands by name

Popular brands