manualshive.com logo in svg

Siemens SCALANCE W734-1, Operating Instructions Manual, Page: 21 / 64

Share
Download
Siemens SCALANCE W734-1 Operating Instructions Manual Download Page 21

 

Description of the device 

 

3.4 Accessories 

SCALANCE W774-1 /W734-1 
Operating Instructions, 01/2017, C79000-G8976-C325-08 

21

 

 

 

NOTICE 
ANT795-4MA 
The ANT795-4MA antenna has degree of protection IP30 and is therefore only suitable for 

dry environments. 

 

 

Note 
ANT793-8DJ 
The antenna ANT793-8DJ may only be used with the flexible connecting cable 6XV1875-

5CH50 (5 m length) or 6XV1875-5CN10 (10 m length). Other flexible connecting cables are 

not permitted. 
Notice for USA/Canada 
Only one antenna per device can be used (connected to R1A1, R1A2 or R2A1, R2A2). 

 

 

Note 
ANT793-8DK 
The antenna ANT793-8DK may only be used with the flexible connecting cable 6XV1875-

5CN10 (10 m length). Other flexible connecting cables are not permitted. 
Notice for USA/Canada 
Only one antenna per device can be used (connected to R1A1, R1A2 or R2A1, R2A2). 

 

 

Summary of Contents for SCALANCE W734-1

































































Reviews:

No comments