Siemens SCALANCE W734-1 Operating Instructions Manual Download Page 63

Page: 63 / 64

SCALANCE W774-1 /W734-1
Operating Instructions, 01/2017, C79000-G8976-C325-08

Index

Antenna cables, 18

Antennas, 18

Connectors, 44

Article numbers, 5

Assembly

DIN rail, 32

S7-1500 standard rail, 31

S7-300 standard rail, 30

Wall mounting, 28

Cables

Permitted lengths, 53, 56

Configuration manuals, 52

C-PLUG, 46

Dimension drawing, 59

Documentation on the CD, 5

Ethernet

Connectors, 42

PoE, 39

Factory defaults, 25, 25, 52

Factory setting, 52

Grounding, 37

Interfaces, 53, 56

KEY-PLUG, 46

LED display, 22

Lightning protection, 36

Loading firmware, 24

Power over Ethernet, 39

Power supply, 39

Primary user (radar), 22

Protective caps, 14

Reset button, 24

Reset device, 25, 25, 52, 52

Reset to Factory Defaults, 52

Resetting the device, 24

Restart of the device, 24

Safety extra low voltage, 36, 37

Safety notices

Use in hazardous areas, 35

when connecting up, 35

Scope of delivery, 14

SELV, 36

Supply voltage, 37

Technical specifications, 53, 56

Terminal block, 14

Type designations, 13

Summary of Contents for SCALANCE W734-1

































































Search results

Summary of Contents for SCALANCE W734-1

Reviews:

Related manuals for SCALANCE W734-1

Brands by name

Popular brands

Siemens SCALANCE W734-1, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE W734-1

Reviews:

Related manuals for SCALANCE W734-1

Brands by name

Popular brands