manualshive.com logo in svg

Siemens SCALANCE M812, Operating Instructions Manual, Page: 42 / 74

Share
Download
Siemens SCALANCE M812 Operating Instructions Manual Download Page 42

Note
Protective ground

A PELV circuit contains a connection to protective ground. Without a connection to protective 
ground, or in case there is a fault in the connection to the protective ground, the voltage for the 
circuit is not stabilized.

Note

Minimum temperature rating of the cable to be connected to the field wiring terminals, 90 °C.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

Do not press the SET button if there is a potentially explosive atmosphere.

WARNING

EXPLOSION HAZARD

Do not connect or disconnect cables to or from the device when a flammable or combustible 
atmosphere is present.

WARNING

Unsuitable cables or connectors

Risk of explosion in hazardous areas
• Only use connectors that meet the requirements of the relevant type of protection.
• If necessary, tighten the connector screw connections, device fastening screws, grounding 

screws, etc. according to the specified torques.

• Close unused cable openings for electrical connections.
• Check the cables for a tight fit after installation.

Connecting up
5.1 Safety when connecting up

SCALANCE M826

42

Operating Instructions, 10/2022, C79000-G8976-C362-07

Summary of Contents for SCALANCE M812











































































Reviews:

No comments