Siemens SCALANCE M812 Page 32 Operating Instructions Manual Download | Manualshive

Page: 32 / 74

background image

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

Replacing components may impair suitability for Class 1, Division 2 or Zone 2.

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I, Zone 2,
the device must be installed in a cabinet or a suitable enclosure.

WARNING

The device may only be operated in an environment of contamination class 1 or 2 (see EN/IEC
60664-1, GB/T 16935.1).

Notes for use in hazardous locations according to ATEX, IECEx, UKEX and CCC Ex
If you use the device under ATEX, IECEx, UKEX or CCC Ex conditions you must also keep to
the following safety instructions in addition to the general safety instructions for protection
against explosion:

WARNING

To comply with EU Directive 2014/34 EU (ATEX 114), UK-Regulation SI 2016/1107 or the
conditions of IECEx or CCC-Ex, the housing or cabinet must meet the requirements of at least
IP54 (according to EN/IEC 60529, GB/T 4208) in compliance with EN IEC/IEC 60079‑7, GB
3836.8.

Safety notices when using according to FM
If you use the device under FM conditions you must also keep to the following safety notices
in addition to the general safety notices for protection against explosion:

WARNING

EXPLOSION HAZARD

The equipment is intended to be installed within an enclosure/control cabinet. The inner
service temperature of the enclosure/control cabinet corresponds to the ambient temperature
of the module. Use cables with a maximum permitted operating temperature of at least 20 °C
higher than the maximum ambient temperature.

Installation and removal
4.1 Safety notices for installation

SCALANCE M826

32

Operating Instructions, 10/2022, C79000-G8976-C362-07

«
...
30
31
32
33
34
...
»

Summary of Contents for SCALANCE M812











































































Reviews:

No comments

Related manuals for SCALANCE M812

Brand: Balanced Body Pages: 4

Brand: Camozzi Pages: 2

Brand: Oktober Pages: 22

Brand: Keiser Pages: 2

Brand: ECA Pages: 3

Brand: Nautilus Pages: 12

Brand: NEC Pages: 54

Brand: Panasonic Pages: 174

Brand: Raymarine Pages: 90

Brand: 4iiii Pages: 36

Brand: 4iiii Pages: 34

Brand: 4EVAC Pages: 27

Brand: AccuMed Pages: 14

Brand: TAS Pages: 25

Brand: Tascam Pages: 80

Brand: Tascam Pages: 2

Brand: Walker Pages: 24

Brand: ZIGBEE Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands